Scheppach HBS400 Original Bedienungsanleitung Seite 26

13. Avoid abnormal posture
- Make sure that you have secure footing and al-
ways maintain your balance.
- Avoid awkward hand positions in which a sudden
slip could cause one or both hands to come into
contact with the saw blade.
14. Take care of your tools
- Keep cutting tools sharp and clean in order to be
able to work better and more safely.
- Follow the instructions for lubrication and for tool
replacement.
- Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
- Check extension cables regularly and replace
them when damaged.
- Keep the handle dry, clean and free of oil and
grease.
15. Pull the plug out of the outlet
- Never remove loose splinters, chips or jammed
wood pieces from the running saw blade.
- During non-use of the electric tool or prior to
maintenance and when replacing tools such as
saw blades, bits, milling heads.
- When the saw blade is blocked due to abnormal
feed force during cutting, turn the machine off
and disconnect it from power supply. Remove the
work piece and ensure that the saw blade runs
free. Turn the machine on and start new cutting
operation with reduced feed force.
16. Do not leave a tool key inserted
- Before switching on, make sure that keys and ad-
justing tools are removed.
17. Avoid inadvertent starting
- Make sure that the switch is switched off when
plugging the plug into an outlet.
18. Use extension cables for outdoors
- Only use approved and appropriately identified
extension cables for use outdoors.
- Only use cable reels in the unrolled state.
19. Remain attentive
- Pay attention to what you are doing. Remain sen-
sible when working. Do not use the electric tool
when you are distracted.
20. Check the electric tool for potential damage
- Protective devices and other parts must be care-
fully inspected to ensure that they are fault-free
and function as intended prior to continued use
of the electric tool.
- Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and
all conditions must be fulfilled to ensure fault-free
operation of the electric tool.
- The moving protective hood may not be fixed in
the open position.
26 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
- Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is speci-
fied in the operating manual.
- Damaged switches must be replaced at a cus-
tomer service workshop.
- Do not use any faulty or damaged connection
cables.
- Do not use any electric tool on which the switch
cannot be switched on and off.
21. Attention!
- The use of other insertion tools and other acces-
sories can entail a risk of injury.
22. Have your electric tool repaired by a qualified
electrician
- This electric tool conforms to the applicable safe-
ty regulations. Repairs may only be performed by
an electrician using original spare parts. Other-
wise accidents can occur.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can
impair active or passive medical implants under
certain conditions. In order to prevent the risk of
serious or deadly injuries, we recommend that
persons with medical implants consult with their
physician and the manufacturer of the medical
implant prior to operating the electric tool.
Additional safety instructions
• Wear safety gloves whenever you carry out any
maintenance work on the blade!
• When cutting round or irregularly shaped wood,
use a device to stop the workpiece from twisting.
• When cutting boards in upright position, use a de-
vice to prevent kick-back.
• A dust extraction system designed for an air veloci-
ty of 20 m/s should be connected in order to comply
with woodworking dust emission values and to en-
sure reliable operation.
• Give these safety regulations to all persons who
work on the machine.
• Do not use this saw to cut fire wood.
• The machine is equipped with a safety switch to
prevent it being switched on again accidentally af-
ter a power failure.
• Before you use the machine for the first time, check
that the voltage marked on the rating plate is the
same as your mains voltage.
• If you use a cable reel, the complete cable has to
be pulled off the reel.
• Persons working on the machine should not be dis-
tracted.
• Note the direction of rotation of the motor and blade.
• Never dismantle the machineʼs safety devices or
put them out of operation.
• Never cut workpieces which are too small to hold
securely in your hand.