DeWalt DWS727 Bersetzt Von Den Originalanweisungen Seite 40

EnGLIsh
Wear ear protection.
Wear eye protection.
Keep hands away from blade.
Visible radiation. Do not stare into light.
Date Code Position (Fig. A)
The date code 8 , which also includes the year of manufacture, is printed
into the housing.
Example:
2019 XX XX
Year of Manufacture
Description (Fig. A1–E)

WARNING: Never modify the power tool or any part of it. Damage or
personal injury could result.
Fig. A1
Lower guard
1
Operating handle
2
Carrying handle
3
Kerf plate
4
Mitre latch button
5
Rail lock knob
6
Rail set screw adjustment
7
8 Date code
Rails
9
Bevel scale
10
Lock down pin
11
Fence adjustment knob
12
Sliding ence
13
Base fence
14
Base extension/carry handle
15
Hand indentation
16
Table
17
Bench mounting holes
18
Mitre scale
19
Dust duct inlet
20
Mitre lock handle
21
Fig. A2
Trigger switch
22
Intended Use
Your D WALT DWS727 mitre saw has been designed for professional
e
cutting of wood, wood products and plastics. When using the appropriate
saw blades, sawing aluminium is also possible. It performs the sawing
operations of cross-cutting, bevelling and mitring easily, accurately
and safely.
DO nOT use under wet conditions or in the presence of flammable liquids
or gases.
This mitre saw is a professional power tool.
DO nOT let children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.
38
Lock-off lever
23
Padlock hole
24
XPS™ on/off switch
25
Wing nut
26
Depth adjustment screw
27
Grooving stop
28
Blade wrench
29
Base
30
31 Bevel lock knob
0° bevel stop
32
Right-hand flip down stop
33
Dust port
34
Belt cover
35
Mitre detent override
36
Optional accessories
Fig. B
DWS5026-XJ Workpiece clamp
37
Fig. C
DW7053-QZ Dustbag
38
Fig. D
DE7023-XJ / DE7033-XJ Leg
39
stand
Fig. E
DE7025-XJ Clamp brackets
40
• Young children and the infirm. This appliance is not intended for use
by young children or infirm persons without supervision.
• This product is not intended for use by persons (including children)
suffering from diminished physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are supervised by a person
responsible for their safety. Children should never be left alone with
this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury, turn
tool off and disconnect tool from power source before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Unpacking (Fig. A1, F)
1. Open the box and lift the saw out by the con venient carrying handle
as shown in Figure F.
2. Place the saw on a smooth, flat surface.
3. Release the rail lock knob 6 , and push the saw head back to lock it in
the rear position.
4. Press down lightly on the operating handle
down pin 11 .
5. Gently release the downward pressure and hold the operating handle,
allowing it to rise to its full height.
Bench Mounting (Fig. A1)
Holes 18 are provided in all four feet to facilitate bench mounting. Two
different-sized holes are provided to accommodate different sizes of screws.
Use either hole; it is not necessary to use both.
Always mount your saw firmly to a stable surface to prevent movement.
To enhance the tool's portability, it can be mounted to a piece of 12.7 mm
or thicker plywood which can then be clamped to your work support or
moved to other job sites and reclamped.
nOTE: If you elect to mount your saw to a piece of plywood, make sure that
the mounting screws don't protrude from the bottom of the wood. The
plywood must sit flush on the work support. When clamping the saw to
any work surface, clamp only on the clamping bosses where the mounting
screw holes are located. Clamping at any other point will interfere with the
proper operation of the saw.

CAUTION: To prevent binding and inaccuracy, be sure the mounting
surface is not warped or otherwise uneven. If the saw rocks on the
surface, place a thin piece of material under one saw foot until the saw
sits firmly on the mounting surface.
Assembling the Base Extensions (Fig. Y)

WARNING: Base extensions must be assembled to both sides of
the saw's base before using the saw.

WARNING: Be sure to adjust the base extensions using the
mounting slots so they are level with the saw's base.
1. Locate the holes above the hand indentations
the base.
2. Using the supplied wrench or a T30 wrench, attach the screw
through the washer 61 , through the base extension
holes on the base.
3. Ensure the extension is secure by pulling on the extension to verify
no movement.
4. Repeat steps 1 through 3 on the other side.
Changing or Installing a New Saw Blade
Removing the Blade (Fig. G1–G4)

WARNING: To reduce the risk of injury, wear gloves when handling
the saw blade.

WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing and
3 ,
2 and pull out the lock
16 on the side of
60
15 , and into the