3M 6000 Serie Bedienungsanleitung Seite 3

GZX
Please read these instructions in conjunction with the 3M™ Facepiece User Instructions where you will nd information on
• Approved combinations of facepieces and lters
• Accessories
• Spare parts
For permitted lter/facepiece combinations see Fig.1.
SYSTEM DESCRIPTION
The Facepiece/Filter combination is designed to remove potentially harmful gases, vapours and particulates from the surrounding atmosphere. Filter
performance data is detailed in the Technical Speci cation.
^ Particular attention should be given to warning statements where indicated.
WARNINGS AND LIMITATIONS
^
Proper selection, training, use and appropriate maintenance are essential in order for the product to help protect the wearer from certain airborne
contaminants. Failure to follow all instructions on the use of these respiratory protection products and/or failure to properly wear the complete product
during all periods of exposure may adversely affect the wearer's health, lead to severe or life threatening illness or permanent disability.
Always be sure that the Facepiece/Filter combination is:
- Suitable for the application;
- Fitted correctly;
- Worn during all periods of exposure;
- Replaced when necessary.
For suitability and proper use follow local regulations, refer to all information supplied or contact a safety professional or 3M on 0870 60 800 60 (UK) or
1800 320 500 (Ireland).
Use this respirator system strictly in accordance with all instructions:
• contained in this booklet
• accompanying other components of the system
• Do not submerge the lters in liquid.
• Do not use in atmospheres containing less than 19.5% oxygen. (3M de nition. Individual countries may apply their own limits on oxygen de ciency.
Seek advice if in doubt).
• Do not use these products in oxygen or oxygen-enriched atmospheres.
• Do not use for respiratory protection against atmospheric contaminants/concentrations which have poor warning properties or are unknown or
immediately dangerous to life and health (IDLH) or against contaminants/concentrations which generate high heats of reaction with chemical lters.
• CAUTION Work with open ames or liquid metal droplets may cause serious risk due to the ignition of lters.
• In case of intended use in explosive atmospheres, contact 3M.
• Do not use in concentrations above those speci ed in the Technical Speci cation.
• Leave the contaminated area immediately if:
a) Any part of the system becomes damaged.
b) Air ow to the facepiece decreases or stops.
c) Breathing becomes dif cult or increased breathing resistance occurs.
d) Dizziness or other distress occurs.
e) You smell or taste contaminants or irritation occurs.
• Never alter, modify or repair this device.
• This product contains no components made from natural rubber latex.
NOTE
Save all user instructions for continuing reference.
Contact 3M for additional information.
PREPARATION FOR USE
Remove the lter from its outer packaging. CAUTION: Care should be exercised when using previously unpacked lters as they may have reduced
service life or may have been used. Check that the lter is appropriate for the purpose – check colour code, letter code and class. Before initial use,
always check that the product is within the stated shelf life (use by date).
ASSEMBLY INSTRUCTIONS
Filter/facepiece assembly instructions.
a) Align 6000 Series lter notch with facepiece mark and push together ( g 2).
b) Turn lter 1/4 turn clockwise to stop ( g 3).
Discard and replace both lters at the same time. Ensure that both lters are of the same type and class. To remove lter, turn ¼ turn anticlockwise
Replace the lter if taste, smell or irritation from gases or vapours is noted, or breathing resistance becomes unacceptable.
The service life of lters will depend upon the activity of the wearer (breathing rate); the speci c type, volatility and concentration of the contaminants; and
environmental conditions such as humidity and temperature.
CLEANING INSTRUCTIONS
Clean with the 3M™ 105 Face Seal Cleaner. Dispose in accordance with national regulations
STORAGE AND TRANSPORTATION
These products should be stored in the packaging provided in dry, clean conditions away from sources of high temperature and petrol and solvent vapours.
Storage conditions on the packaging refer to annual average temperature and relative humidity values.
indicates acceptable storage conditions. X indicates unacceptable storage conditions. See Figure 4.
Storage under conditions other than those speci ed by the manufacturer may affect the shelf life.
3