Cleaning And Maintenance; Technical Data - Clatronic mc 1034 cd Bedienungsanleitung

MORY. Use the SKIP+/SKIP- buttons (7/8/1) to select the
desired track and then press the PROGRAM button again.
The display changes to memory slot 02.
3. Select the next track with the SKIP+/SKIP- key and press
the PROGRAM key again. Repeat the procedure until all the
desired tracks are selected.
NOTE:
Once the storage capacity of the tracks to be programmed
has been reached, the memory preset number „P01"
appears in the display.
4. Press the PLAY/PAUSE key (12/5). The playback starts.
PLAY MEMORY appears in the display. Press this button
to pause briefl y the playback.
5. Press once the STOP key to stop the playback while
retaining the program. The MEMORY control lamp goes out.
6. To resume the playback of the program press fi rst the
PROGRAM key once and then the PLAY/PAUSE key.
7. In order to delete the programme, press the PROGRAM
button in stop mode. Then keep the STOP button pressed
down for approx. 3 sec.
The device stops automatically once the entire sequence of
programmed tracks is completed. The programmed order of
tracks remains in the memory until you change to a different
mode, remove the CD from the CD compartment or switch off
the device.
It is also possible to combine the programmed tracks with the
REPEAT function. After you have programmed and started
the device, please press the REPEAT button (9/2) up to three
times and then you can use the functions as described under
„REPEAT".
NOTE:
Please note these instructions for playing back CDs and
CDRs in MP3 format!
The device is not able to play back MP3 fi les. The CD
begins to turn, but the sound cannot be heard.
Please note:
There are a number of different recording and compression
methods, as well as quality differences between CDs and self-
recorded CDs.
Furthermore, the music industry does not adhere to fi xed
standards (copy protection).
For these reasons that there may occasionally be problems with
the playback of CDs. This is not a malfunction of the device.

Cleaning and Maintenance

• Always remove the mains plug before cleaning the machine.
• Any marks on the surface can be wiped off with a slightly
damp cloth without any additives.
32
05-MC 1034 CD.indd 32 05-MC 1034 CD.indd 32
NOTE: COMPACT DISKS
• This device is able to play CDs with a diameter of
8 cm and 12 cm.
NOTE:
Only place one disc in the CD compartment at a time.
• Only audio CDs, CD-R and CD-RW disks can be played
on this machine.
• Always place the CD into the CD compartment with the
label facing upwards. Compact discs can only be played
on one side.
• Fingerprints and dust should be carefully removed from
the recorded side of the CD (the side without the label)
with a soft cloth. Wipe off in straight lines from the centre
to the edge.
• After being played, CDs should be returned to their case
so that they do not become scratched.
• Do not expose CDs to direct sunlight, high humidity levels
or prolonged high temperatures in order to prevent them
from warping.
• Do not adhere any paper to the CD or write on it.
• Do not spray any cleaning agents or antistatic sprays on to
the CD as in the case of phonographs.
Troubleshooting
Symptoms Course
CD can not be CD is not inserted
played back. or inserted incor-
rectly.
CD jumps during Check the disc for
playback. fi ngerprints, dirt or
scratches.

Technical Data

Model: ................................................................... MC 1034 CD
Power supply: ........................................................ 230 V, 50 Hz
Power consumption: ...........................................................13 W
Protection class: .......................................................................ΙΙ
Net weight: ........................................................................ 4,3 kg
Radio section:
Frequency ranges: .................. VHF / FM 88,0 ~ 108,0 MHz
....................... MW / AM 540 ~ 1600 kHz
This device has been tested according to all relevant current
CE guidelines, such as electromagnetic compatibility and low
voltage directives, and has been constructed in accordance with
the latest safety regulations.
Subject to technical changes without prior notice!
Solution
Ensure that the
disc is inserted with
the label facing
upwards.
Check the disc for
fi ngerprints, dirt or
scratches.
05.02.2008 14:43:35 Uhr 05.02.2008 14:43:35 Uhr