Symbols Used; In The Documentation; Warning Notices - Structure And Meaning; Symbols In This Documentation - Bosch TTM 2104 Originalbetriebsanleitung

1.

Symbols used

1.1

In the documentation

1.1.1 Warning notices -
Structure and meaning
Warning notices warn of dangers to the user or
people in the vicinity. Warning notices also indicate
the consequences of the hazard as well as preventive
action. Warning notices have the following structure:
KEY WORD – Nature and source of hazard!
Warning
symbol
Consequences of hazard in the event of
failure to observe action and information
given.
¶
Hazard prevention action and information.
The key word indicates the likelihood of occurrence
and the severity of the hazard in the event of non-
observance:
Key word Probability of
occurrence
DANGER Immediate impending
danger
WARNING Possible impending
danger
CAUTION Possible dangerous
situation
1.1.2

Symbols in this documentation

Symbol Designation Explanation
Attention Warns about possible property damage.
!
Information Practical hints and other
i
useful information.
1. Multi-step Instruction consisting of several steps.
2. operation
One-step Instruction consisting of one step.
e
operation
Intermediate An instruction produces a visible

result intermediate result.
Final result There is a visible final result on
"
completion of the instruction.
1.2

On the product

!
Observe all warning notices on products and ensure
they remain legible.
Robert Bosch GmbH
Severity of danger if
instructions not observed
Death or severe injury
Death or severe injury
Minor injury
Symbols used | TTM 2104 / TTM 2204 | 33 | en
2.

Important notes

Before start up, connecting and operating
Bosch products it is absolutely essential
that the operating instructions/owner's
manual and, in particular, the safety
instructions are studied carefully. By doing so you can
eliminate any uncertainties in handling Bosch products
and thus associated safety risks upfront; something
which is in the interests of your own safety and will
ultimately help avoid damage to the device. When a
Bosch product is handed over to another person, not
only the operating instructions but also the safety
instructions and information on its designated use must
be handed over to the person.
2.1

FCC Compliance (USA)

TTM 2104 / TTM 2204 complies with the requirements
of Section 15 of the FCC Rules. The following
conditions apply regarding operation:
R
TTM 2104 / TTM 2204 must not cause any harmful
disruptions;
R
TTM 2104 / TTM 2204 must be immune to
interference and permit reception of interference,
including interference that can cause unwanted
operation.
TTM 2104 / TTM 2204 has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference in a residential installation.
TTM 2104 / TTM 2204 may generate, use and
emit energy at radio frequencies that can disrupt
radio communication if installed improperly or
used in a manner inconsistent with the operating
instructions. However, there is no guarantee that
interference will not occur in a particular installation.
If TTM 2104 / TTM 2204 does cause harmful
interference to radio or television reception, which can
be determined by turning TTM 2104 / TTM 2204 off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
R
Reorient or relocate the receiving antenna.
R
Increase the separation between
TTM 2104 / TTM 2204 and receiver.
R
Connect TTM 2104 / TTM 2204 into an outlet on a
circuit different from that to which the receiver is
connected.
R
Consult the dealer or an experienced radio/TV
technician for help.
All changes or modification to the
TTM 2104 / TTM 2204 that are not expressly allowed
by Robert Bosch GmbH can result is loss of permission
to operate TTM 2104 / TTM 2204 .
|
1 691 206 005 2019-02-25