Trouble Shooting; Spare Parts/Accessories; Guarantee; Possible Cause - Parkside PTK 2000 D3 Originalbetriebsanleitung

Trouble shooting

Problem
1. Blade dissolves after swit-
ching off the engine
2. Engine will not start
3. Motor wrong direction of
rotation
4. Motor will not work, the
fuse is activ
5. Fire marks on the cutting
surface

Spare parts/Accessories

If you do not have internet access, please contact the Service Centre via telephone (see "Service-Center" page 18). Please have the
order number mentioned below ready.
(6) Parallel stop, complete ....................... Order-No. 91103530
(40) Transverse stop. .............................. Order-No. 91103531
(2) Blade guard, complete ....................... Order-No. 91104563
(17) Table length extender ....................... Order-No. 91104557
(5) Table insert ....................................... Order-No. 91104566
(7) Table width extender (right) ................ Order-No. 91104561
(7) Table width extender (left) ................... Order-No. 91104562
(35) Laser .............................................. Order-No. 91104558
(3) Riving knife ....................................... Order-No. 91104559

Guarantee

Dear Customer,
This equipment is provided with a 3-year guarantee from the date
of purchase.
In case of defects, you have statutory rights against the seller of
the product. These statutory rights are not restricted by our guar-
antee presented below.
Terms of Guarantee
The term of the guarantee begins on the date of purchase. Please
retain the original receipt. This document is required as proof of
purchase.
If a material or manufacturing defect occurs within three years of
the date of purchase of this product, we will repair or replace –
at our choice – the product for you free of charge. This guarantee
requires the defective equipment and proof of purchase to be pre-
sented within the three-year period with a brief written descrip-
tion of what constitutes the defect and when it occurred.

Possible cause

To slightly tightened fastening nut
a) Failure mains fuse
b) Defective extension cable
c) Connections on motor or switch not in order
d) Motor or switch faulty
a) Capacitor faulty
b) Wrong connection
a) Cross section of the extension cable does not
suficiently
b) Overload by a blunt saw blade
a) blunt saw blade
b) wrong saw blade
Spare parts and accessories can be obtained at
www.grizzly-service.eu

Fault correction

Tighten the right hand thread nut
a) Check mains fuse
b) Replace extension cord
c) Repair by electrical specialist
d) Repair by electrical specialist
a) Repair by electrical specialist
b) Exchange polarity of outlet by an
qualiied electrician
a) see „Electrical connection"
b) Change saw blade
a) Sharpen or change saw blade
b) Change saw blade
(11) Handwheel, complete ....................... Order-No. 91104560
(19) Push stick ........................................ Order-No. 91104950
(14) On/off switch, complete ................... Order-No. 91104952
(24) Stand brackets (both sides) ............... Order-No. 91103542
(23) Rubber feet ..................................... Order-No. 91104951
(4) Saw blade 24 Teeth .......................... Order-No. 13800400
(4) Saw blade 48 Teeth ........................... Order-No. 13800401
(15) Collection bag ................................. Order-No. 91104556
If the defect is covered by our guarantee, you will receive either
the repaired product or a new product. No new guarantee peri-
od begins on repair or replacement of the product.
Guarantee Period and Statutory Claims for Defects
The guarantee period is not extended by the guarantee service.
This also applies for replaced or repaired parts. Any damages
and defects already present at the time of purchase must be re-
ported immediately after unpacking. Repairs arising after expiry
of the guarantee period are chargeable.
Guarantee Cover
The equipment has been carefully produced in accordance with
strict quality guidelines and conscientiously checked prior to
delivery.
GB IE NI
17