FARFISA INTERCOMS ZHEROS ZH1252B Handbuch Seite 16

forward the fl oor call and with microswitches SW2 set the
room number 0 (see table on page 39); press for a long
time key until a tone will confi rm the occurred storing.
Attention: when forwarding a fl oor call, all video
intercoms (both main and secondary) present in the
apartment to which the fl oor call was forwarded will
ring.
To change the stored address, it is necessary to set with
SW1 and SW2 the new codes and press for a long time key
until a tone will confi rm the occurred storing; instead, to
delete the stored address, it is necessary to set code 255
on SW1 and 0 on SW2 (see table on page 39) and press
for a long time key until a tone will confi rm the occurred
cancellation.
4.1.5 Additional Addresses
A video intercom can be enabled to receive also the calls
addressed to other users (max 4); for the programming of
the relative addresses it is necessary to proceed as follows:
- with microswitches SW1 set the address of the fi rst user
for whom it is desired to answer and with microswitches
SW2 the relative room number (see table on page 39);
press for a long time key
occurred storing of the fi rst address. If it is intended to
programme other additional addresses, it is necessary to
set microswitches SW1 with the address of the second
user for which it is desired to answer and microswitches
SW2 with the relative number of room (see table on page
39); press for a long time key
the occurred storing of the second address. Proceed in
a similar way for the programming of the address of the
third and fourth user for which it is desired to answer; the
occurred programming is confi rmed respectively by three
or four tones.
To change the stored addresses, it is necessary to exit
from the programming, wait 3 seconds and re-enter into
the programming; set with SW1 and SW2 the new codes
and press for a long time key
the occurred storing of the new fi rst additional address;
proceed in a similar way to change the eventual second,
third and fourth address. To delete stored addresses, it is
necessary to set code 255 on SW1 and 0 on SW2 (see table
on page 39) and press for a long time key
will confi rm the occurred cancellation of the fi rst address;
proceed in a similar manner to cancel any second, third
and fourth stored address.
4.1.6 Exit from the system programming
To exit from programming, jumper J4 must be taken from
position 1-2 to position 3-4, icon
4.2 Video intercom programming
For programming of the device it is necessary to set the
codes that identify the video intercom respectively inside
the plant (user addresses from 001 to 200) and inside the
apartment (room number from 0 to 3).
For user address keep in mind that:
- it must not be the same number of another apartment;
if more internal stations in parallel are in the apartment,
they must have the same user address but different
room number (see next paragraph);
until a tone will confi rm the
until two tones will confi rm
until a tone will confi rm
until a tone
will turn off.
- it must coincide with the number stored in the external
keyboard and in the possible reception switchboard;
- it must be stored in the key call or in the device contacts of
another user if it is necessary to intercommunicate between
the two apartments.
For the number of room, keep in mind that:
- the number of room establishes also a hierarchy in the
internal device, as the device that will have room number
0 (zero) will be defi ned as the main, while all others will
be secondary;
- the different number of room allows carrying out and
selectively receiving calls between devices within the same
apartment; the calls from outside or from another apartment
will ring up all the devices, the fi rst to answer will activate
the conversation and will turn off the ringtones of the others;
- upon arrival of a call from an external video intercom station,
all the devices will ring, but only the main (number of room
0 "zero") shows the image of the camera. From the other
video intercoms of the same apartment, it is possible to view
the entry by pressing key
ringtones, turns on the video intercom and simultaneously
turns off the main video intercom.
4.2.1 User Address and number of room.
To program the address and the room number of the video
intercom no procedure is needed, just place microswitches
SW1 and SW2 in accordance with the table on page 39;
(from factory the video intercom is programmed with user
address 100 and room number 0).
Attention: since microswitches SW1 and SW2 are used
to perform also other programming (see paragraph 4.1
System Programming), their position may have been
changed.
Before using the device remember to position
microswitches SW1 and SW2 in accordance with
the user address and the room number that it is
intended to be given to the video intercom.
- 16 -
. This operation deactivates all
Mi 2515