Nice neomat H Anweisungen Und Hinweise Für Den Installateur Seite 6

If you need to erase all the data contained in the memory of the con-
trol unit in the NEOMAT H motors, carry out the following procedure.
The memory can be erased:
• with a previously memorised transmitter (table "A9")
• with a non-memorised transmitter (table "A10").
Table "A9" Erasing the memory with a previously memorized transmitter (fig. 13)
Press and hold down button ■ of a transmitter until you hear a beep
1.
(after about 5 seconds)
Press and hold down key ▲ on the transmitter until you hear 3 beeps; release key ▲
2.
exactly during the third beep.
Press and hold down key ■ on the transmitter until you hear 3 beeps; release key ■
3.
exactly during the third beep.
➨ Press and hold down key ▼ on the transmitter until you hear 3 beeps; release key ▼
4.
exactly during the third beep.
If you wish to erase all the data, press the ▲ and ▼ keys together within 2 seconds and
5.
then release them.
After a few seconds 5 beeps will signal that all the memorised codes have been erased.
In order to erase the memory using a non-memorized remote control, proceed as follows:
Table "A10" Erasing the memory with a non-memorized transmitter (fig. 14)
1. Switch off the power supply for at least 3 seconds.
2. Switch the power back on and within 10 seconds rotate the rod for emergency manoeuvre
device for at least 6 turns.
3. At this point, within 1 minute, you can proceed to erase the memory following the procedure
described in table "A9", using any remote control, even a non-memorized one.
If the application requires it, the awning can be automated using the VOLO S RADIO wind and sun sensor. This sensor, when properly memo-
rised in the motor, will ensure that the awning is extended when the sun is shining and that it is retracted when the wind rises. For a detai-
led description of the performances and programming of the sensor levels refer to the instructions for the VOLO S RADIO product.
5) What to do if...
When the motor is switched on, the 2 beeps do not sound.
Make sure the motor is powered with the correct voltage; if the pow-
er input is correct there is probably a serious fault and the motor
needs replacing.
After a radio command, 6 beeps are heard and the
manoeuvre does not start
The radio control unit is unsynchronised, repeat the transmitter
memorisation process.
After a command, 10 Beeps sound and then the manoeu-
vre begins
The auto-diagnosis of the memorised parameters has detected a
fault (positions, programming, direction of movement are incorrect).
Check and repeat programming if necessary.
After a command the motor does not turn.
• The thermal protection might have triggered; in this case just wait
for the motor to cool down
• ∑ If a wind sensor has been memorized, the set threshold might
have been exceeded.
• You might try to switch the motor off and back on again; if the 2
beeps do not sound, there is probably a serious fault and the
motor needs replacing.
During the UP phase, before reaching the set position
(pos. "0", pos. "I"), the motor stops and then makes 3
attempts to start up again.
This does not necessarily mean trouble: in case of overload during
6
a small troubleshooting guide!
The following can be erased:
• only the transmitter codes, finishing at point N. 4
• all the data (transmitter codes, positions, RDC function, etc.), com-
pleting the procedure.
the UP phase the motor is switched off for 1 second and then
attempts to complete the manoeuvre. Check to see if any obstacles
are obstructing movement.
During the DOWN phase, before reaching the set position
(pos. "1", pos. "I"), the motor stops.
This does not necessarily mean trouble: in case of overload the
motor is switched off. Check to see if any obstacles are obstructing
movement.
The motor turns only if the control is manned.
If positions "0" and "1" have not been programmed the motor rolls
the awning up or down only through manual control. Program posi-
tions "0" and "1".
Positions "0" and "1" have been programmed, but the
awning moves down only if the control is manned.
The emergency manoeuvre has probably been used, or the motor
has remained switched off for over 24 hours. Give the command to
raise the awning and wait for it to reach position "0".
Example
5s
5s
within 2 s
Example
3s
X6
within 10s
"Table A9"