Standard Equipment - Virutex FR66P Gebrauchsanweisung

router.
- Always guide the router with both hands using
the two knobs J (Fig. 1), with stop lever B (Fig. 1)
within easy reach.
- Following completion of a job, disconnect the motor
and release the base before leaving the router.
- Always place the router on the base, on a fl at,
clean surface.
- Always use the lever of the main switch to turn
the router on.
- Ensure that the router cannot accidentally fall
over.
- Use only bits of diameter suitable for the chuck to
be used, and adapted to the router speed.
- The specifi cations of the bits of the VIRUTEX
range are especially adapted to the performance
of this router. Use preferably bits from the extensive
VIRUTEX range, or only bits whose characteristics
conform to the said specifi cations.

4. STANDARD EQUIPMENT

You will fi nd the following items inside the box:
- Surface router FR66P
- Size 26 service key
- Template guide diameter 19 for 26 mm dove-
tailing
- Lateral fence unit
- Aspiration connector
- Instruction manual and other documentation
5. STARTING UP THE MACHINE
Cut-out box A (Fig. 1) is equipped with lever B
(Fig. 1), which can be pressed with a fi nger. This
enables the user to start it up or stop it with no need
to move his hand from knob. To do this, activate
the switch's lateral stop C (Fig. 1) and, without
releasing it, push forward lever B. Stop C prevents
the machine from starting up accidentally.
6. ASSEMBLY OF THE CUTTING TOOLS
Assemble cutting tool D (Fig. 2, 3) in chuck E (Fig.
2), block the axis by pressing brace F (Fig. 3) and
insert wedge G (Fig. 3) to lock the fastening in
place. Tighten nut H (Fig. 2, 3) with the service
key I (Fig. 3).
WARNING!
Avoid leaving the machine with no tools installed,
since the chuck could be overtightened and da-
mage the shaft.
7. BLOCKING OF THE BASE
The base can be locked in any position using
knob J (Fig. 1). When knob is loosened, the base
will automatically return to its highest position
due to the action of the springs incorporated in
the columns.
6
WARNING!
Following completion of any job, fl ick the switch to
OFF and release the base using knob before leaving
the router, which must be on a fl at surface.
8. ADJUSTING THE DEPTH
ADJUSTING THE DEPTH. The depth is adjusted
using the incorporated rack and pinion depth-ad-
justment mechanism. With the cutter bit face fl at
against the wood surface, the penetration depth
may be adjusted to up to 60 mm.
To unlock the depth rod K (Fig. 4) press down
fi rmly on adjustment knob L (Fig. 4) and turn it to
raise or lower the depth rod, if a greater or lesser
cutting depth is required. The gauged adjustment
indicator M (Fig. 4) can be moved separately from
the knob, so that it may be set to zero from any
position using the reference mark. When turning
the knob after adjusting the indicator, both elements
will turn together, thereby indicating the degree to
which the rod has been moved. A full turn of the
knob moves the rod by 34 mm, with a maximum
distance of 55 mm.
To hold the depth rod in the required position,
release the pressure from the adjustment knob.
Next, to ensure that the knob is fi rmly held in place,
it should be locked using fastening knob N (Fig. 4).
PRECISION ADJUSTMENT. If you wish to make
precision adjustments to the previously set depth,
simply turn adjustment knob O (Fig. 4).
A full turn of the knob moves the rod by 1 mm,
with a maximum distance of 5 mm. Each division
in the gauged fi ne-adjustment indicator P (Fig. 4)
represents a movement of 0.1 mm.
MAKING DEEP CUTS. To perform cuts that are too
deep to carry out with a single cut, we recommend
making several successive cuts using the six 3-mm
steps in the revolving depth turret Q (Fig. 4).
Lower the machine until the cutting bit is level with
the surface on which the router is resting. Use
locking knob J (Fig. 1) to hold the machine in this
position. Loosen fastening knob N (Fig. 4), then
press down and turn adjustment knob L (Fig. 4)
until the depth rod presses against the lower step
of the revolving depth turret, using fi ne adjustment
if required. In this position, turn depth indicator M
(Fig. 4) until position zero matches the reference
mark. This will be the starting position indicating
the point at which the bit comes into contact with
the material. Hold the rod in place with knob N
(Fig. 4), release the locking knob and leave the
machine in the off position.
Loosen fastening knob N, then press down and
turn adjustment knob L, moving the adjustment
rod K (Fig. 4) upwards to the required cut depth.
Then use knob N once again to turn turret Q (Fig.