Installation Of Front And Side Panels; Control Panel And Functions; Setting The Water Temperature; Water Heating Temperature ("Set Point") - Jacuzzi city spa Montageanweisung

u Press the TEST button of the differential switch located up-
stream from the electrical system to which the spa is connected.
If it does not trip, it may be faulty or it may have tripped due to
problems in the electrical system of the building.
Disconnect the spa and do not use it until you have identi-
fied and eliminated the defect.
u Check the operation of the hydromassage pumps using the
key (upon pressing the key for the first time, the pump is acti-
vated; it is turned off by pressing the key a second time).
u Check that the spotlights switch on and off using the key
u Check that there are no leaks from the hydraulic connections
or other problems.
u Completely disinfect the spa by carrying out "super-chlorin-
ation" treatment (it is also referred to as schock treatment, see
the user manual, chapter "Water treatment").
This operation is recommended when installing, or after a long pe-
riod of not using the spa.
u After a few hours, turn off the omnipolar switch.
u Open the drain valve(s) and completely empty the spa.
u If included, re-install the front and side panels.
CAUTION
Do not use the spa the first time you start it as there is a
high concentration of chlorine in the water during this
phase. Immediately empty the bath.
Contact the local authorities for the standards govern-
ing the discharge of chemically treated water.
u Close the drain valve(s) and fill the spa again with fresh water
as previously explained.
u Turn the omnipolar switch back on and check that the spa
works correctly.
u Check and as necessary modify the water filtering cycles
based on how you intend to use the spa.

■ Installation of front and side panels

(where included)
Consult the drawings and information relevant to the supplied model.
✐
u (
2, part.1) Insert the rubber spacers on the threaded pins
(located on the lower part of the support legs).
✐
u (
2, part.2) Set one of the two panels with corners (A-B) at
the edge of the tub and check that the slots on the lower bracket
coincide with the threaded pins.
✐
u (
2, part.3-4) Insert the edge of the upper bracket in the
under-edge profile. Then set the panel next to the tub, so that
the threaded pins are inserted into the slots. (part.5)Temporarily
fasten the panel with the indicated nuts.
u Install the other panel in the same way.
u Using the same procedure, install the front panels (C and D). To
make insertion easier, if necessary pull out on panels A and B.
Finally, make sure the panels are aligned with one another.
u Permanently secure the panels by tightening the nuts all the
way, until any vertical gaps are closed between the panel and
the corner.
.

Control panel and functions

✐
( 5) All spa functions are managed by the control panel on the
tub, as are the respective settings/programming.
NOTE: the display is equipped with keys "
or decrease the values.

■ Setting the water temperature

The water is heated by a tubular electrical heater. Do not set an
excessively high water temperature, i.e. over the limit of 40 °C. The
recommended temperature is 35-36 °C.
NOTE: with the version with 1.5 Kw heater, when the pump is
activated, the heater is turned off (the LED relative to the symbol
flashes) and is turned on once again after the pump has been
switched off.

Water heating temperature ("set point").

To check or modify the water heating temperature, do the following:
u Press keys "
" or "
memorized temperature.
u Keep keys "
" or "
sented, from a minimum of 15 °C to a maximum of 40 °C
NOTE: press the " "
decrease it.
u To show the temperature of the water in the tub again, do
not touch any key for about 5 seconds.
u As soon as the water temperature set point is reached, the
heater is shut off. It will not be turned back on until the water
temperature drops about 0.5 °C below the set point.
u To ensure precise measurement of the water temperature,
the filtering pump comes on every half hour for about 30 sec-
onds (even if no filtering cycles were set), since the temperature
probe is located in the heater pipe.
NOTES
When the system is turned off, or there is a power outage, the last
set point is stored in memory.
Operation of the heater is shown on the display by a LED on
steady under the symbol
25 25
" and "
": the display will show the current
" pressed down to change the value pre-
key to increase the value or the
.
" to increase
" "key to