Preparing The Base Tool - Acument Avdel Genesis G2-s Betriebsanleitung

A c c e s s o r i e s
P r e p a r i n g t h e b a s e t o o l
•
Disconnect the air supply.
•
Remove any nose assembly items.
•
Remove retaining nut 26 and all elements
of the stem collector (items 18
22, 23, 24, 25. Note that 'O' ring 19
remains.
•
Replace the above with a safety cap as
shown in drawing opposite.
•
Unscrew jaw spreader housing 1 and
remove with 'O' ring 2, locknut 3, seal
housing 6.
•
Screw stop nut 71210-20202 onto the
front of head piston 8 as far as it will go
by hand.
•
Re-fit jaw spreader housing 1 and 'O' ring
2.
•
Unscrew the stop nut until it locks against
jaw spreader housing 1 and tighten with
spanner.
The tool is now ready to be fitted with a swivel
head. Instructions are on page 14.
R I G H T - A N G L E S W I V E L H E A D c a p a b i l i t y
FASTENER
1
MATERIAL
NAME Ø
1 / 8 3.2
AVEX Aluminium Alloy
®
1 / 8 3.2 Steel
5 / 32 4.0 Aluminium Alloy
5 / 32 4.0 Steel
3 / 16 4.8 Aluminium Alloy
BULBEX 5 / 32 4.0 Aluminium Alloy
®
4.8 Aluminium Alloy
3 / 16
AVINOX 1 / 8 3.2 Stainless Steel
®
4.0
5 / 32 Stainless Steel
– 4 Aluminium Alloy
AVSEAL ®
– 4
Aluminium Alloy
– 5 Aluminium Alloy
– 5
Aluminium Alloy
1 / 8 3.2 Steel
STAVEX ®
4.0
5 / 32 Steel
1 / 8 3.2 Stainless Steel
4.0
5 / 32 Stainless Steel
1 / 8 3.2 Aluminium Alloy
AVDEL
®
1 / 8 3.2 Aluminium Alloy O
1 / 8 3.2 Stainless Steel
5 / 32 4.0 Aluminium Alloy
5 / 32 4.0 Aluminium Alloy O
3 / 16 4.8 Aluminium Alloy
4.8 Aluminium Alloy O
3 / 16
MBC 1 / 8 3.2 Aluminium Alloy
4.0 Aluminium Alloy
5 / 32
3 / 16 4.8 Aluminium Alloy
3.2 Aluminium Alloy
MBC L/C 1 / 8
5 / 32 4.0 Aluminium Alloy
4.0 Aluminium Alloy O
5 / 32
3 / 16 4.8 Aluminium Alloy
1
In inches then in millimetres.
Item numbers in bold refer to the general assembly drawings and parts lists pages 22-25.
Base tool to receive a nose assembly
,
21
20, 21,
22
23
Base tool to receive a swivel head
SWIVEL HEAD
PART Nº
07346-03000
07346-03100
07346-03100
07346-03200
07346-03200
07346-03100
07346-03200
07346-03100
07346-03200
07495-04000
07495-04700
07495-04100
07495-04800
07346-03100
07346-03200
07346-03100
07346-03200
07346-03300
07495-03600
07495-03000
07346-03400
07495-03700
07346-03500
07495-03800
07346-04000
07346-04100
07346-04200
07346-04500
07346-04500
07346-04600
07346-04600
2
Long nose tip for deep placing.
18 18
20 20 19
27
26
25
24
71210-20201
SAFETY CAP
NOSE TIP (mm)
PART Nº 'A' 'B'
07345-03600 7.87 3.81
07345-03700 7.87 3.81
07345-03700 7.87 3.81
07345-03800 7.87 3.81
07345-03800 7.87 3.81
07345-03700 7.87 3.81
07345-03800 7.87 3.81
07345-03700 7.87 3.81
07345-03800 7.87 3.81
07494-06001
6.35 1.95
2
6.35 4.11
07494-06601
7.62 2.00
07494-06101
2 7.62 4.11
07494-06701
7.87 3.81
07345-03700
7.87 3.81
07345-03800
7.87 3.81
07345-03700
7.87 3.81
07345-03800
5.08 1.17
07345-03301
07494-03601 5.08 1.17
5.08 3.81
07494-03011
07345-03401 6.6 0.84
6.6 0.84
07494-03701
07345-03501 8.13 0.25
8.13 0.25
07494-03801
4.75 1.9
07165-00701
6.35 2.36
07165-00702
7.92 2.46
07165-00703
7.87 2.03
07345-04701
7.87 2.03
07345-04701
7.87 2.03
07345-04701
7.87 2.03
07345-04701
COMPLETE TOOL PART NUMBER :
A
(the stop nut and safety cap are included)
IMPORTANT: by opposition to complete tools
B
with nose assemblies, those fitted with swivel
heads include the nose tip as a part of the head.
O
Oversize
E n g l i s h
3
6
8
71210-20202
STOP NUT
see
JAWS
below
PART Nº
07340-00213 ... 0 0 1
... 0 0 4
07340-00213
07340-00213 ... 0 0 4
... 0 1 0
07490-04602
07490-04602 ... 0 1 0
07340-00213 ... 0 0 4
07490-04602 ... 0 1 0
07340-00213 ... 0 0 4
07490-04602 ... 0 1 0
07340-00213 ... 1 6 0
07340-00213 ... 1 8 0
07340-00213 ... 1 6 1
07340-00213 ... 1 8 1
07340-00213 ... 0 0 4
... 0 1 0
07490-04602
07340-00213 ... 0 0 4
... 0 1 0
07490-04602
07340-00229 ... 2 8 3
... 2 8 4
07340-00229
07340-00213 ... 2 8 5
... 2 8 8
07340-00229
07340-00229 ... 2 8 9
07498-04401 ... 2 9 3
07498-04401 ... 2 9 4
07340-00229 ... 3 0 0
07340-00229 ... 3 0 5
07498-04401 ... 3 1 0
07340-00229 ... 3 2 0
07340-00229 ... 3 2 0
07498-04401 ... 3 2 7
07498-04401 ... 3 2 7
precede with 71400-40
1
2
13