Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
14.3.2
General data
Description
Pump output
[l/h]*
Metering back-pressure [MPa (bar)]
Number of strokes [1/min] in metering mode:
Metering quantity/stroke [ml]
Metering accuracy (see chapter 14.6)
max. conveyable viscosity [mPas]
Permissible ambient temperature
Suction height [mWS] at 100 % stroke
max. suction-side pre-pressure [MPa (bar)]
noise level (DBA) at a distance of 1m (acc. to DIN EN 12639/ EN ISO 9614-2)
Recommended minimum diameters
Weight [kg]
*
Values determined with water as the metering medium at a temperature of 20°C.
**
Suction heights determined with clean, moistened valves at max. stroke frequency
ATTENTION
14.3.3
Input/output wiring (also see chapter
14.3.3.1 Control inputs
Inputs
Level pre-
warning
Empty
Batch
Pulse
Metering lock
Standard
signal
Diaphragm
breakage
monitor
Metering
monitor
14.3.3.2 Control outputs
Outputs
External
supply
Stroke signal
Empty/reserve/
fault signal
417102214_EDPL_V60.docx
in metering mode:
setting**
With reference to DIN EN 809 5.2.3, please be advised that the surface temperature of the
motor and frequency convertor may exceed 80°C under certain circumstances.
Therefore, ensure that these areas cannot be touched during operation!
Assign.
External wiring
Terminal X1
Pin
1
+
3
Terminal X1
Pin
2
+
3
Terminal X1
Floating contact
Pin
4
+
3
Attention: Do not connect any external voltage!
Terminal X1
Pin
6
+
7
Terminal X1
Pin
8
+
7
External current
Terminal X1
Input is not floating!
Pin
9
+
10
Attention:
Take note of the polarity of the connected signal!
Terminal X2
Electronic switch
Pin:
13
+
14
Voltage supply through a 5 V output/pump
+
15
+
16
(terminal X2, pins 15 + 16)
Terminal X2
Floating contact
Pin
20
+
21
Attention: Do not connect any external voltage!
Assign.
External wiring
Floating contact
Terminal X1
Attention: Do not connect any
Pin
5
+
3
external voltage!
External voltage
Terminal X1
Attention: Take note of the polarity
Pin
11
+
12
of the connected signal!
Terminal X3
External voltage
Pins
1
+
2
high / low
medium / medium
low / high
high / low
medium / medium
low / high
Suction connection [ID mm]
Pressure connection [ID mm]
7.2.4
"Terminal strip overview")
Values
Supply for external devices:
Output 5V DC, max 50 mA
Max. external voltage 24 V DC, max 0.3 A
When stopped: contact open
Max. external voltage 230 VAC/DC, max 3 A
in reserve signal:
Contact closed for approx. 500 ms
Contact open for approx. 500 ms
117
Pump type
02200
04800
06700
220
480
670
183
400
558
147
320
447
1,0 (10)
0,6 (6)
0,4 (4)
120
100
80
30,6
66,7
93,1
< ± 3%
600 mPas
5-40°C
2
0.2 (2)
66,0
DN 20
DN 25
DN 30
DN 12
DN 20
DN 25
26.7
28.5
30
Values
min. on/off time 15 ms
0/4-20 mA,
Load approx. 50 ohms
Rev. 1.12.11
Werbung
Kapitel
Inhaltsverzeichnis
Fehlerbehebung
