Technische Daten; Maintenance And Storage - WOODLINE WL 13 C/1000 EL Bedienungs- Und Wartungshandbuch

4) TECHNISCHE DATEN

D
WL13/16 C/1000
L
MODEL HUB SPALTÄGE
mm mm
WL 13 C/1000 1000 1100
EL
WL 13 C/1000 1000 1100
C
WL 13 C/1000 1000 1100
AP
WL 13 C/1000 1000 1100
C+EL
WL 13 C/1000 1000 1100
ii
WL 16 C/1000 1000 1100
EL
WL 16 C/1000 1000 1100
C
WL 13 C/1000 1000 1100
AP
WL 16 C/1000 1000 1100
C+EL
WL 16 C/1000 1000 1100
ii
WL 20 C/1000 1000 1100
EL D.P. 2+2
WL 20 C/1000 1000 1100
C
WL 20 C/1000 1000 1100
AP
WL 20 C/1000 1000 1100
C+EL
WL 20 C/1000 1000 1100
ii
5) TRANSPORT UND INBETRIEBNAHME
Vor der Durchführung von Eingriffen an der Maschine das vorliegende Bedienungshandbuch
WL 20 C/1000
H
L
T
MOTOR SCHUB ZYKLUS BEHÄLTER GEWICHT ABMESSUNGEN
Ton sec. Öl L
Stand./auf. Viskositätswert cSt
380V-50HZ 12,2 32/20 16
4 Kw 15 a 40°C
- 12,2 14/9 18
15 a 40°C
- 12,2 14/9 18
15 a 40°C
380V-50HZ 12,2 - 18
4 Kw 15 a 40°C
- 12,2 - -
380V-50HZ 15,4 35/20 18
4 Kw 15 a 40°C
- 15,4 16/10 19
15 a 40°C
- 12,2 14/9 18
15 a 40°C
380V-50HZ 15,4 - 20
4 Kw 15 a 40°C
- 15,4 - -
380V-50HZ 18 18/11 25
4 Kw 15 a 40°C
- 18 18/11 25
15 a 40°C
- 18 18/11 25
15 a 40°C
380V-50HZ 18 - 28
4 Kw 15 a 40°C
- 18 - -
vollständig lesen.
7.4) Emergency blade stop:
In any emergency situation, release the control levers to make
the blade return to the starting position.
7.5) Stop of the Log-splitter
7.5.1) Stopping the motor (electric powered models):
To stop the motor, press the red button on the switch.
Never stop the motor when it is under pressure.
H
Do not exert prolonged blade pressure on a log that will not split. Prolonged pressure will cause
the hydraulic circuit and the motor to overheat.
Modulate the pressure applied to the levers to reduce the speed and increase the motor power, or return
the log-pusher to the cycle start position, turn the log 90° and repeat the cutting cycle.
7.5.2) Stopping the machine (models powered by tractor p.t.o.):
Reduce the p.t.o. rotation speed gradually until it stops.
Avoid jerky variations in the p.t.o. rpm, as this could damage the overgear – pump unit.
7.5.3) Stopping the machine (models with hydraulic clutches):
T
Stop the hydraulic pump as described by the tractor manufacturer.
7.6) Adjusting the blade starting position:
Kg mm
To cut short logs and quicken the work, the blade stroke can be adjusted
by moving the stroke adjustment pawl (D) using the tightening key.
295 1200x2600x760
To carry out this operation, lower the blade to the stroke end, loosen the
pawl key (D), slide the rod (E) to the required height, and then lock the
280 1200x2600x760
key back into position.
280 1200x2600x760
7.7) Adjusting the stroke block (lower/raise):
305 1200x2600x760
With work table (optional) fitted.
After fitting the table (see accesories manual), adjust the stroke
240 1200x2600x760
limit of the wedge using the lower pawl (F) to block it at about
5 cm above the level of the table; this will prevent the lowering
335 1200x2600x760
of the wedge from damaging the table.
With work table (optional) not fitted.
325 1200x2600x760
To adjust the stroke, lower the wedge until the cylinder stroke
is at its terminal point (when the pressure is prolonged, the
280 1200x2600x760
wedge does not descend any further), then raise it slightly (about
345 1200x2600x760 1 cm) and use the lower pawl (F) to block the stroke limit.
290 1200x2600x760

8) MAINTENANCE AND STORAGE

450 1450x2550x870
8.1) Level of hydraulic oil:
440 1450x2550x870
440 1450x2550x870
To check the level of the hydraulic oil, look through the level cap
on the side of the frame (L).
460 1450x2550x870
400 1450x2550x870
5 cm
PIANO OPTIONAL
L
31
WL 13-16-20 C/1000
GB
E
D
F