Technical Data - Bosch PWR 180 CE Originalbetriebsanleitung

OBJ_BUCH-2193-004.book Page 25 Friday, September 9, 2016 9:08 AM
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3: a
2
K=1.5 m/s .
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.

Technical Data

Wall processing system
Article number
Handpiece
Rated power input
Rated speed
Max. outer diameter of application
tool
Thread of sander spindle
Thread length (max.) of sander
spindle
Reduced starting current
Constant electronic control
Speed preselection
Soft starting
Restarting Protection
Overload Protection
Weight according to
EPTA-Procedure 01:2014
Protection class
Dust container (Accessory)
Filter system
Container volume
Weight according to
EPTA-Procedure 01:2014
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Bosch Power Tools
Assembly
2
=7.5 m/s ,
h
 Before any work on the machine itself, pull the mains
plug.
Mounting application tools
 Wear protective gloves when changing application
tools/accessories. Contact with the application tool/ac-
cessory can lead to injuries.
Different application tools are available depending on the ma-
terial to be worked and the desired material removal rate on
the surface.
An overview of the right choice of application tool for an appli-
cation together with a speed recommendation can be found in
section "Selection of the Application Tool and Speed Setting",
page 27.
Note: Do not put the handpiece 1 down without an applica-
tion tool mounted on it (sanding plate, wire brush, perforator,
cup wheel, backing pad, etc.). The brush collar 12 may be-
come bent and damaged as a result.
Changing the Sanding Sheets
The surface of the sanding plate 37 is fitted with Velcro back-
ing for quick and easy fastening of sanding sheets with Velcro
adhesion.
PWR 180 CE
– When attaching a new sanding sheet, remove any dust or
3 603 CC4 0..
debris from the sanding plate 37, e. g., with a brush.
– Position the sanding sheet 38 flush to the edge of the sand-
ing plate 37, then place the sanding sheet on the sanding
W 1010
plate and press it on firmly.
-1
min 410–1650
– To remove the sanding sheet 38, lift it from the side and
pull it off of the sanding plate 37.
mm 180
Changing the Application Tools
M 14
 Actuate the spindle lock button only when the sander
spindle is at a standstill. Otherwise, the machine may be-
mm 22
come damaged.

 Use only carbide cup wheels with a flat

sanding surface.


– Clean the sander spindle 14 and all parts to be mounted.
 – To clamp and loosen the application tool, lock the sander
spindle with the spindle lock button 3.

– To fasten the application tool, screw the mounting flange
15 onto the sander spindle 14 and then tighten the mount-
kg 3.6
ing flange 15 by hand.
/II
– Put the spring washer 16 on the sander spindle 14.
– Working with wire brush, perforator, cup wheel, sand-
ing plate/sanding sheet (see figure A):
Membrane
Attach the desired application tool to the sander spindle
filter
14.
l 3
Screw on the clamping nut 17 and tighten it with the two-
pin spanner 18.
kg 2.5
Note: Pay attention that the collar of the clamping nut 17
faces away from the machine, as shown in the figure.
– Working with backing pad and foam disc for polishing:
Screw the backing pad 39 onto the sander spindle 14 until
the backing pad is firmly against the spring washer 16.
Tighten the backing pad 39 with an open-end spanner.
English | 25
1 609 92A 1LR | (9.9.16)