Finish Operation - Kärcher SP 2 Flat Bedienungsanleitung

Inhaltsverzeichnis

Verfügbare Sprachen

NOTICE

The shorter the hose length and the larger the hose di-

ameter, the higher the pump capacity.

To prevent clogging of the pump, use a prefilter with

hose diameters of less than 1¼ " (see special accesso-

ries).

The pump connection is equipped with a plug system

(Quick-Connect).

The unmounted connection nozzle is enclosed in the

device.

Illustration

 To remove the connection nozzle, press the Quick-

Connect (grey button).

Illustration

 Slide the hose clamp onto the hose.

If a ¾" or 1" hose is used:

 Screw pump connecting piece (see special acces-

sory) onto the connection nozzle.

 Slide the hose onto the pump connecting piece and

secure it by means of a hose clamp.

 Slide the connection nozzle into the Quick-Connect.

If a 1¼ " hose is used:

 Slide the hose onto the connection nozzle and se-

cure by means of a hose clamp.

 Slide the connection nozzle into the Quick-Connect.

Illustration

 Folding the support legs in and out (SP 2 Flat - see

operation).

 Safely place the pump on a stable surface in the

feed fluid or immerse it using a rope tied to the car-

rying handle.

NOTICE

The suction area must not be blocked by soiling.

In case of muddy ground, place the pump on a brick or

the like.

Ensure that the pump is level.

Do not carry the pump on the cable or the hose.

DANGER

Risk of mortal danger on account of electric shock!

Do not touch feed fluids, the rope attached to the carry-

ing handle as well as objects that are in contact with the

feed fluid (e.g. pipelines extending into the water, rail-

ings, etc.).

Automatic venting device

Illustration

With a low fluid level, possibly drawn air or air that is

present in the pump escapes via the automatic venting

device. In addition, fluid may leak at this spot.

If the pump has suction problems with a low fluid level,

unplug and plug in the mains plug repeatedly in order to

support the suction process.

Start up

Operation

Automatic operation

Illustration

 Fold out the support legs (SP 2 Flat) for the pump

start if necessary.

NOTICE

It is not mandatory to fold out the support legs; a higher

pump capacity is achieved by folding out the support legs.

Illustration

NOTICE

In the automatic mode, the float switch controls the

pumping operations automatically .

The pump switches on as soon as the float switch has

reached the switch-on height due to the rising fluid level.

The pump switches off as soon as the float switch has

reached the switch-off height due to the falling fluid level.

Ensure that the float switch is not obstructed in any way.

For switch-on height / switch-off height see the following

table:

Min / Max

Switch-on height

cm*

Switch-off height

cm*

*The switching height can vary depending on the posi-

tion of the float switch.

 Insert the mains plug into the socket.

Illustration

 Fold in the support legs (SP 2 Flat) for the pump

start.

NOTICE

By folding in the support legs the flat vacuuming of the

fluid up to a residual fluid height of 1 mm becomes pos-

sible in manual operation.

Illustration

 Secure the float switch pointing upwards in the

lock.

NOTICE

In manual operation the pump remains switched on

continuously.

In order that the pump draws independently in manual

operation, the fluid level must be at least 60 mm (SP 1

and 3 Dirt) or 7 mm (SP 2 Flat).

The pump can pump up to a residual fluid height of

25 mm (SP 1 and 3 Dirt) or 1 mm (SP 2 Flat).

The stated residual fluid height is only achieved in man-

ual operation.

 Insert the mains plug into the socket.

ATTENTION

Risk of damage! Dry running leads to increased wear;

never leave the pump unattended during manual oper-

ation. Switch off immediately in case of dry running.