Villeroy & Boch Design Line Benutzerhandbuch Seite 36

Hardware Setup/Wiring Diagram BFBP21S (50 Hz Just Silence)
J25=HTR1
J9
J26=HTR2
J27=HTR3
J30=TEST
J46
J31=CE
HTR
SEL
K2
F6 30A
J60 J41
TB1
1
2
BLU
BRN
3
GRN
4
4
230V
1þ
1x32A
230V
1þ
1x16A
SETUPS 3 & 4
ONLY
Settings
SINGLE SERVICE TWO-SERVICE 230V
230V 1þ / 1x32A,
LOCATION DEVICE
J9 NETZSTROMVERSORGUNG 2-GESCHW.-PUMPE 1 ALIMENTATION POMPE 1 A 2 VITESSES 2-SPEED PUMP 1
J14 NETZSTROMVERSORGUNG 2-GESCHW.-PUMPE 2 ALIMENTATION POMPE 2 A 2 VITESSES 2-SPEED PUMP 2
PUMP 2 LINE 1 CONNECTION
J21 KREISLAUF PUMPE POMPE DE CIRCULATION CIRC PUMP
CIRC AND OZONE LINE 1 CONNECTION
J32 N/A
J33 TV / AV
J40 IR RECIEVER
J5, J8 AUX PANEL(S) - AX10, AX20, AX30, AX40
SETUP # CIRC PUMP
1* PROGRAMMABLE FILTRATION + POLLING
2*
3 PROGRAMMABLE FILTRATION + POLLING
4
PUMP 1 LOW TIMEOUT IS 60 MINUTES.
LOCATION DEVICE VOLTS
J1 ON OZONE 230V
EXPANDER + EXT.
BOARD XP332 LIGHTING
RED
TO
WHITE
J1 ON
EXPANDER
GREEN
BLACK
WHITE
TO (GROUP 2)
GREEN
ON MAIN BOARD
2016 V&B Owners Manual.indd 42
34
J21
J32
J33
K9
J13
K4
J38
J39 K8
J19
J10 J43
K12
230V
F8 30A
J24
115V 115V
J109
1
T1
F3 0.125A 240V
K1
K3
2
J44
J49 J48
2 3
K5
J15
3
UNUSED
J53 J58
F4 3A SLO-BLOW
J111
GND
J11
ON
S1
SENSOR A SENSOR B
3.0 kW HEATER
THREE-SERVICE
1þ / 2x16A, 230V 1þ / 3x16A
J19 to J43
J81 to J59
PUMP 1 PUMP 2 TEMP SCALE
SYSTEM WILL BE IN
2-SPEED 2-SPEED °C
2-SPEED 2-SPEED °C
2-SPEED °C
2-SPEED °C
MAX AMPS
1A USING SPLITTER
TB1
230V 2þ / 2x16A
1
2 BRN
2
1 BLU
OZONE
1 BRN
3
2 BLU
GRN
4
EXT. LIGHTING
PUMP 2 IS USED IN SETUPS 1 & 2 ONLY
2.5HP (10.3A MAX) PUMPS REQUIRE 1þ / 3x16A
J14
SERVICE WHEN SYSTEM IS CONFIGURED IN SETUP 1 OR 2.
K6
J50
J34 J35
MAIN MAIN
J5
J108 J107
J91
AUX
J101
J27
J23
SERIAL
J22
J26 J30
J8
J25 J31
AUX
J29
J40
VAC
K7 HTR
REMOTE
DISBL
10
J17 J16
AUX
J28 FRZ
230V 1þ
1x32A
230V 2þ
2x16A
230V 3þ
3x16A
CIRC PUMP OPTION
PROGRAMMABLE FILTRATION CYCLES +
POLLING
USED IN SETUPS 1 & 3
SETUP #2
UNLESS MARKED
DIFFERENTLY
BELOW
J60 J41
230V 3þ / 3x16A
1
1 BRN
2 BRN
J3
2 X-B
3 BRN
EXPANDER
W12
3
J53 J58
J38
4
J46
BFBP21S – PN 56708
01-23-15
IR Receiver WiFi
OR Transceiver
RF Receiver J34 OR J35
LOCATION DEVICE VOLTS AMPS FROM
J1 ON OZONE+EXT 230V 2A W1 ON
EXPANDER LIGHTING MAX EXPANDER
EXPANDER RIGHT
X-P332 J7
EXPANDER
BOARD
W1
J6
F1 30A
J1
INSTEAD OF SETUP #2,
THIS SYSTEM IS
CONFIGURED IN SETUP #:
SYSTEM WILL BE SHIPPED IN SETUP #2
UNLESS MARKED OTHERWISE
SWITCHBANK S1 OFF
TEST MODE OFF A1 TEST MODE ON
DON'T ADD 1 HS PUMP W/HTR
A2 ADD 1 HS PUMP WITH HEAT
DON'T ADD 2 HS PUMPS W/HTR A3 ADD 2 HS PUMPS WITH HEAT
DON'T ADD 4 HS PUMPS W/HTR
A4 ADD 4 HS PUMPS WITH HEAT
SPECIAL AMPERAGE RULE A A5 SPECIAL AMPERAGE RULE B
STORE SETTINGS** MEMORY RESET**
A6
NOT ASSIGNED A7 NOT ASSIGNED
NOT ASSIGNED A8 NOT ASSIGNED
NOT ASSIGNED
A9 NOT ASSIGNED
NOT ASSIGNED A10 NOT ASSIGNED
6
**SWITCH # SHOULD BE SET TO OFF UPON FINAL INSTALLATION.
* 2.5HP (10.3A MAX) PUMPS REQUIRE
1þ / 3x16A SERVICE WHEN SYSTEM IS
CONFIGURED IN SETUP 1 OR 2.
J46
J60 J41
1
TB1
1
2
2
BLU
3
3
GRN
4
J53 J58
4
BFBP21S – PN 56708
01-23-15
TP (MAIN) PANELS
J34 OR J35
J5 (A1-A4)
AUX OR
J8 (A5-A8)
TO FROM TO
GROUP 2 J6 ON GROUP 3
J1 EXPANDER J58
FOR SUPPLY CONNECTIONS,
USE CONDUCTORS SIZED ON THE
BASIS OF 60°C AMPACITY BUT
RATED MINIMUM OF 90°C.
USE COPPER CONDUCTORS ONLY.
EMPLOYER UNIQUEMENT
DES CONDUCTEURS DE CUIVRE.
TORQUE RANGE FOR
MAIN TERMINAL BLOCK (TB1):
27-30 IN. LBS.
(31.1-34.5 kg cm)
PART A
SWITCHBANK S1 ON
230V 1þ 1X16A
OFF ON
A2
A3
A4
J3 X-B
J38
EXPANDER
W12
PART B
42
4/26/2016 1:02:17 PM
PA