Mains Connection; Fuse Protection - ATIKA AH 402 Bedienungsanleitung

Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician or
one of our customer service points. Local regulations –
especially regarding protective measures –
observed.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service points.
Use only original spare parts, accessories and special
accessory parts. Accidents can arise for the user through
the use of other spare parts. The manufacturer is not
liable for any damage or injury resulting from such action.
S
S
Check that the machine is completely and correctly
assembled.
To avoid toppling, place the shredder on a firm horizontal
surface.
Do not place the equipment on ground which is paved or
surfaced with gravel.
The machine should only be operated in the open. Always
maintain a safe distance (at least 2 m) from walls or other
fixed objects.
Before using the shredder, make sure each time that
there are no faulty connections (tears, cuts, etc.)
−
there are no damage at the machine
−
all screws are tight
−

Mains connection

Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the machine to the
relevant and properly earthed plug.
Only use connection cables with sufficient diameters

Fuse protection

2400 W 16 A träge
2500 W
Switch on and off
Switching on
Press the green I button.
Switching off
You can switch off the shredder by
pressing the red 0 button of the
switch.
Lock in case of power outage
The equipment will
automatically if there is a power cut (zero-voltage initiator).
Repress the green button to switch it on again.
t a r t - u p
t a r t - u p
only UK / Switzerland
13 A träge
A
switch off
Motor guard
The motor is equipped with a guard switch and it switches off
automatically when overloaded. The motor can be switched on
again after a cooling-down period (approximately 5 mins.).
Repress
1. button A
must be
2. button green I to switch it on again.
Electrical mains supply impedance
When conditions in the electrical mains supply are un-
favourable, voltage reductions for short periods can occur during
the process of turning on the equipment, which can adversely
affect other equipment (e.g., the flickering of a lamp).
No breakdowns are to be expected if the maximum, electrical
mains supply impedances given in the table are met.
Power consumption P
2400 – 2500
W o r k
W o r k
Choose a working position alongside the equipment or
behind it. Never stand near the ejecting opening.
Never reach into the filling or ejection opening.
Keep your face and body away from the filling opening.
Never place hands, other parts of the body or clothing into
the filler funnel, ejection channel or in the vicinity of other
moving parts.
Check that no shredded residues are in the filling hopper
before switching on the equipment.
Do not tip or tilt the machine when the motor is running.
When filling, be careful that no pieces of metal, stones,
bottles or other objects unintended for processing, enter the
filling hopper.
Immediately switch off the equipment and allow it to come to
a stop, if foreign objects enter the filling hopper or if the
equipment starts to make unusual noises or vibrates.
Remove the mains plug and carry out the following checks:
inspect for damage,
−
replace or repair damaged parts,
−
− check the equipment and tighten loose parts.
You must not repair the equipment yourself if you are
unauthorized to do so.
What can I shred?
Yes:
• organic household and garden waste
e. g. hedge and tree cuttings, dead flowers and vegetable
kitchen waste.
No:
• glass, metal, plastic, plastic bags, stones, cloth, roots with
soil, food left-overs, fish or meat.
13
(watts) Electrical mains supply
1
impedance Z
i n g w i t h t h e g a r d
i n g w i t h t h e g a r d
(Ω)
max
0,24
e n s h r e d d e r
e n s h r e d d e r