Kärcher WPD 100 Advanced Originalbetriebsanleitung Seite 30

E411 Filter change required
E412 Level sensor carbonator defective
E413 Check water supply
E500 Malfunction hot water
All red LEDs are on
E501 Malfunction hygienisation power failure
All red LEDs are on
E502 Malfunction water in the device
All red LEDs are on
E503 Malfunction water in the base
All red LEDs are on
E504 Malfunction buttons
All red LEDs are on
E505 Malfunction hygienisation sensor hot
All red LEDs are on
E506 Malfunction hygienisation sensor cold
All red LEDs are on
E507 Malfunction hygienisation sensor ambient
All red LEDs are on
E508 Malfunction temperature heating module too high
All red LEDs are on
E509 Malfunction hot sensor
All red LEDs are on
E510 Malfunction ambient sensor
All red LEDs are on
E511 Malfunction cold sensor 1
All red LEDs are on
E512 Malfunction cold sensor 2
All red LEDs are on
E513 Malfunction cooling 1 defective
All red LEDs are on
E514 Malfunction cooling 2 defective
All red LEDs are on
E515 Malfunction cooling 1
All red LEDs are on
E516 Malfunction cooling 2
All red LEDs are on
E600 Malfunction electronics
All red LEDs are on
E601 Malfunction electronics
All red LEDs are on
E602 Malfunction electronics
All red LEDs are on
E603 Malfunction electronics
All red LEDs are on
E604 Malfunction electronics
All red LEDs are on
E610 Invalid device code
30
Exceeding a maximum run time (device
run time) for the various filters (1 year).
Level sensor CO mixer defective.
2
No or insufficient water inflow.
Heating module defective.
Hygienisation was not successful
Water leakage inside the device.
Leakage inside the base.
Buttons defective.
Hygienisation was not successful
Hygienisation was not successful
Hygienisation was not successful
Heating module.
Sensor hot water defective.
Sensor unchilled water defective.
Sensor cooling module 1 defective.
Sensor cooling module 2 defective.
Cooling module 1 defective
Cooling module 2 defective
Temperature cooling module 1 too low.
Temperature cooling module 2 too low.
Malfunction unit control on the control
panel.
Malfunction unit control of the display.
Malfunction unit control base board.
The temperature of the unit control is too
high.
Malfunction unit control of the brightness
sensor.
The setting of the device code is incorrect Inform service.
13
-
EN
Change the filter.
E400: Replace Active-Pure filter
E401: Replace Hy-Protect filter
E402: Replace Hy-Pure filter (WPD 100)
Set the appliance switch to "0".
Set the appliance switch to "I".
If it is occurs again, contact service.
Clean the inlet sieve in the water connection (see "Care and mainte-
nance/cleaning inlet sieve").
Check water connection.
Set the appliance switch to "0".
Set the appliance switch to "I".
If it is occurs again, contact service.
Set the appliance switch to "0".
Inform service.
Start the hygienisation again.
Set the appliance switch to "0".
Inform service.
Set the appliance switch to "0".
Switch the machine back on again.
If it is occurs again, contact service.
Start the hygienisation again.
If it is occurs again, contact service.
Set the appliance switch to "0".
Restart the device after approx. 10 minutes.
If it is occurs again, contact service.
Set the appliance switch to "0".
Inform service.
Set the appliance switch to "0".
Restart the device after approx. 5 minutes.
If it is occurs again, contact service.