General Rules Of Safety - Nice UST1 Anweisungen Und Hinweise Für Installation Und Bedienung

ENGLISH

GENERAL RULES OF SAFETY

KNOWLEDGE OF THE SYSTEM
AND PREPARATION FOR INSTALLATION
CONTROL AND CONNECTION ELEMENTS
MECHANICAL LIMIT SWITCH SETTING
MOTOR CONNECTION CABLES
UST1 ELECTRONIC BOARD - CONNECTIONS
UST1 WIRING DIAGRAM
TECHNICAL DATA - FEATURES
TRANSPORT / STORAGE / DISPOSAL
TECHNICAL ASSISTANCE / SPARE PARTS /
ACCESSORIES
EC DECLARATION OF CONFORMITY
GENERAL RULES OF SAFETY
The planning and production of the devices that form the UST1control
unit, and the instructions in this manual are perfectly compliant with
the current safety standards. Nevertheless, an incorrect installation
can cause serious injury to the persons that work on the plant or that
use it. For this reason, during installation it is important to follow all the
instructions for use containedin this manual.
Do not start installation if you have any doubts of any kind
and, if necessary, contact the Nice Assistance Service.
WORK IN SAFE CONDITIONS!
ATTENTION! – It is important to follow these instructions for
reasons of safety.
ATTENTION! – Scrupulously preserve the safety instructions.
Strictly follow these instructions.
– Make only the electrical connections described in this
manual for use: incorrect wiring can cause serious damage
to the plant.
– In the case of use outdoors, the power supply cable supplied
must totally be protected with a special protection pipe.
In view of the risks associated with the installation and with
system control, it is necessary to install the product following
these instructions:
– Execute only the modifications described in this manual for use.
Any other modification can cause serious mal f unctio n ing. The
manufacturer declines all responsibility for any damages caused by
arbitrary modifications introduced to the devices.
– Do not position the devices near sources of heat or unprotected
flames. This can cause malfunctioning, fire and other dangers.
– During installation the devices should not be immersed in water or
other fl uids. Prevent the infiltration of fluids into the devices.
– The packaging material must be disposed of in strict observance of
current regulations.
ATTENTION!! – Preserve this manual for use with utmost care to
make device disposal or maintenance operations easier in the future.
KNOWLEDGE OF THE SYSTEM
AND PREPARATION FOR INSTALLATION
Description and use
1
1
UST1 is a control unit for rolling shutters and sectional doors with
2
three-phase or single-phase motors. All the common safety elements
can be connected.
4
With the application of various bus connections (modules), other
6 - 8
applications are possible.
9
Just press the special button installed on the cover or the outside
10
button to open or close a door.
11
It is possible to open and close the door wirelessly in automatic mode.
11
Any other use is considered improper! The manufacturer
11
declines all responsibility whatsoever for damages caused
by improper use of the various system devices not compliant
with what is indicated in this manual for use.
The plant manufacturer is responsible for the complete plant. He must
fulfil the current regulations and directives (e.g. DIN 1986, EN 12050).
He is responsible for drawing up the technical documentation of the
entire plant to be supplied together with the plant.
It is necessary to comply with the provisions and national
and local regulations regarding installation, as well as the
accident prevention rules in force.
Disconnect the system from the electrical power supply
during works.
Checks before installation
Carefully read these assembly and use instructions before beginning
installation of the control unit.
The manufacturer declines all responsibility and obligation of warranty
if any arbitrary changes in construction are made without previous
written authorisation or installation not compliant with the assembly
instructions is executed.
The plant manufacturer must ensure that the EMC directives, low
voltage directives, machinery directives and directives on construction
products are observed.
ATTENTION!
This control unit cannot be used in areas at risk of explosion.
ATTENTION!
Connect the power supply cable to terminal X1 (L1, L2, L3) and to the
PE terminal of the main board.
The power supply cable must be protected on-site with 3 x 10 HV
fuses.
The fuse must have a value such that the gearmotor makes the fuse
trip if it becomes blocked.
WARNING! To avoid the damage of the motor as the result of the loss
of one phase of the 3-phase motor supply, it is necessary to install a
phase loss detector on the power line. This device is not provided with
the product, and should be purchased separately by the installer.
English – 1