Safety Warnings And Precautions; Installation Warnings; Operation Warnings - Nice To-Max A Installierungs-Und Gebrauchsanleitungen Und Hinweise

ENGLISH
SAFETY WARNINGS AND
1
PRECAUTIONS
1.1 - SAFETY WARNINGS
• CAUTION! – Follow these personal safety instruc-
tions very carefully. Incorrect installation could cause
serious physical injury. Therefore, before starting work
carefully read all parts of the manual and if in any doubt
contact the Nice Service Centre for clarifications.
• CAUTION! – All product installation, connection,
programming and maintenance operations must be
performed exclusively by a qualified and skilled
technician, in observance of laws, standards and
local regulations and the instructions in this manual.
• CAUTION! – Important safety instructions; save
these instructions for future use. Keep this manual in
a safe place to enable future product maintenance and
disposal procedures.

1.2 - INSTALLATION WARNINGS

• Before starting installation, check that the specific mo -
tor model is suitable for the automation of your shutter
(see paragraph 3.1). If not suitable, do NOT proceed
with installation.
• All preliminary set-up work, including cable laying, as -
sembly of automation devices and electrical connec-
tions, with the exception of the system connection
to the mains, may be performed by personnel with
standard skills, provided that all instructions in this ma -
nual are strictly observed in the specified order.
• Connection of the automation to the mains must be
performed by a skilled and qualified electrician, in
observance of local current safety standards and these
instructions (see paragraph 4).
• All installation and maintenance operations must be
performed with the automation disconnected from the
2 – English
power supply. If the power disconnect device is not vis-
ible from the location of the shutter, a suitable notice
must be affixed on the switch stating "WARNING! MA -
INTENANCE IN PROGRESS".
• Before starting installation, all unnecessary electrical
cables must be removed and all mechanisms not re -
quired for motorized shutter operation must be disab led.
• If the product is installed at a height of less than 2.5 m
from the floor or other support surface, the moving par -
ts must be protected with a suitable covering, to avoid
inadvertent access. For protection, refer to the instruc-
tion manual of the shutter, ensuring that future access
for maintenance purposes is guaranteed.
• During installation, handle the tubular motor with care
to avoid crushing, impact, dropping or contact with liq-
uids of any type (fig. 1). Never drill or apply screws on
the tube containing the motor. Keep the tubular motor
away from sources of strong heat and ensure that it is
not exposed to flames. This may damage system com-
ponents and cause malfunctions or hazardous situa-
tions. If this occurs, suspend installation immediately
and contact the Nice Service Centre for assistance.
• During installation, no screws must be fitted on the
roller section crossed internally by the tubular motor.
This could cause damage to the motor.
• The power supply cable is in PVC to guarantee suitabil-
ity for installation exclusively indoors.
• During installation handle the tubular motor power ca -
ble with care. If subject to damage, this may constitute
a hazard.
• If the power cable is damaged, the product cannot be
used as the cable cannot be replaced. Therefore con-
tact the Nice Technical Assistance.
• During installation or programming of the tubular motor,
keep all persons away from the shutter when moving.
• The list of accessories available can also be consulted
on the site www.niceforyou.com

1.3 - OPERATION WARNINGS

• The product should not be used by children or people
with impaired physical, sensorial or mental capacities or
who have not received adequate training in the safe use
of the product.
• Do not allow children to play with fixed control devices.
Keep portable (remote) control devices out of children's
reach.
• Check the automation frequently to detect possible
imbalance, signs of wear or damage. Suspend use im -
mediately if maintenance is required.
• Check the automation during a manoeuvre, ensuring
that there are no persons in the vicinity of the shutter
until the movement is completed.
• Never activate the automation if anyone is performing
work nearby, such as cleaning windows; disconnect
the power supply before these operations.
• Packaging material must be disposed of in full obser-
vance of current local legislation.
• Take care to conserve this manual to facilitate future
programming or maintenance of the product.