Personnel Qualifications; Warranty - Wilo -Drain TP 100E Einbau- Und Betriebsanleitung

1 Introduction
1.1 About this document
The language of the original operating instructions is
German. All other languages of these instructions are
translations of the original operating instructions.
This manual is divided into individual sections, which
are listed in the table of contents. Each section has a
meaningful heading which clearly describes its content.
A copy of the EC-Declaration of conformity is a com-
ponent of these operating instructions.
If a technical modification is made on the designs
named there without our agreement, this declaration
loses its validity.

1.2 Personnel qualifications

All personnel who work on or with the device must be
qualified for such work; electrical work, for example,
may only be carried out by a qualified electrician. All
personnel must be of legal age.
National accident prevention regulations must also be
observed as a basis by the operating and maintenance
personnel.
It must be ensured that personnel have read and
understood the instructions in this operating and main-
tenance manual; if necessary, this manual must be
ordered from the manufacturer in the required lan-
guage.
This device is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision and instruc-
tion concerning use of the device by a person responsi-
ble for their safety.
Children should be supervised to ensure that they do
not play with the device.
1.3 Copyright
This operating and maintenance manual has been cop-
yrighted by the manufacturer. The operating and main-
tenance manual is intended for use by installation,
operating and maintenance personnel. It contains tech-
nical regulations and drawings which may not be repro-
duced or distributed, either completely or in part, or
used for purposes of competition, or shared with oth-
ers without the express consent of the manufacturer.
The illustrations used may differ from the original and
are only intended as an exemplary representation of
the pumps.
1.4 Subject to change
The manufacturer reserves the right to make technical
modifications to systems and/or components. This
operating and maintenance manual refers to the device
indicated on the title page.
Installation and operating instructions Wilo-Drain TP 80, TP 100

1.5 Warranty

In general, the specifications in the current "General
Terms and Conditions" apply to the warranty. You can
find these here:
www.wilo.com/legal
Any deviations must be contractually agreed and shall
then be given priority.
1.5.1 General
The manufacturer is obliged to correct any defects
found in the devices it sells, provided that the defects
meet one or more of the following requirements:
• The defects are caused by the materials used or the
way the product was manufactured or designed
• The defects were reported in writing to the manufac-
turer within the agreed warranty period
• The pump was used only as intended
• All monitoring devices are connected and were tested
before commissioning
1.5.2 Warranty period
The duration of the warranty period is stipulated in the
"General Terms and Conditions".
Any deviations must be contractually agreed!
1.5.3 Spare parts, add-ons and modifications
Only genuine spare parts from the manufacturer may
be used for repairs, replacements, add-ons and modifi-
cations. Unauthorised attachments and modifications,
or the use of non-genuine parts, can lead to severe
damage to the device and/or to personal injury.
1.5.4 Maintenance
The prescribed maintenance and inspection work
should be carried out regularly. This work may only be
carried out by qualified, trained and authorised person-
nel.
1.5.5 Damage to the product
Damage and malfunctions that endanger safety must
be eliminated immediately and properly by trained per-
sonnel. The device may only be operated if it is in per-
fect working order.
In general, repairs should only be carried out by Wilo
customer service!
1.5.6 Exclusion from liability
No warranty is granted and no liability is accepted for
damage to the device if one or more of the following
apply:
• Inadequate configuration by the manufacturer due to
the information provided by the operator or customer
being insufficient or incorrect
• Non-compliance with safety instructions and working
instructions as specified in this operating and mainte-
nance manual
• Improper use
• Incorrect storage and transport
• Improper installation/dismantling
• Insufficient maintenance
English
23