Introduction; Device Description (Fig. 1-10); Scope Of Delivery; Intended Use - Parkside PWDS 920 A1 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

1. Introduction

MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment and suc-
cess.
NOTE:
According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service techni-
cians,
• Installation and replacement of non-original spare parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due to
the non-compliance of the electric regulations and VDE
regulations 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating instructions
before installing and commissioning the device.
The operating instructions are intended to help the user to
become familiar with the machine and take advantage of its
application possibilities in accordance with the recommen-
dations.
The operating instructions contain important information
on how to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, reduce
downtimes and how to increase reliability and service life
of the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt
and moisture. Read the instruction manual each time before
operating the machine and carefully follow its information.
The machine can only be operated by persons who were
instructed concerning the operation of the machine and who
are informed about the associated dangers. The minimum
age requirement must be complied with.
In addition to the safety notes contained in the present oper-
ating instructions and the special regulations of your country,
the generally recognized technical rules for the operation of
machines must be observed.
We accept no liability for damage or accidents which arise
due to non-observance of these instructions and the safety
information.

2. Device description (Fig. 1-10)

1. Grinding plate
2. Front handle
3. Wing nut
4. LED-Light
5. Setting speed range
6. Locking knob
7. Main Handle
8. Power Cord
9. Additional Handle
10. Connection for dust extractor
11. Telescopic extension
12. Lock for telescopic extension
13. ON/OFF switch
14. Flexible suction hose
15. Hose adaptor
16. Sanding paper
17. Allen Key
18. Screwdriver
19. Carbon brushes

3. Scope of delivery

1 Drywall sander
1 flexible suction hose (14)
6 abrasive sheets (16) (different grain sizes)
1 Phillips screwdriver (18)
2 replacement carbon brushes (19)
1 Allen key (17)
1 Cotter pin (C)
• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport dam-
age.
• If possible, store the packaging until the warranty period
has expired.
ATTENTION
The device and packaging materials are not toys! Chil-
dren must not be allowed to play with plastic bags, film
and small parts! There is a risk of swallowing and suf-
focation!

4. Intended use

The intended use of this power tool is the sanding of large
areas of drywalls as a preparation before painting or wall-
papering using suitable abrasive sheets.
This power tool is neither suited for the preparation of small
areas, corners and edges, nor for the removal of wallpaper
and the grinding of ceilings and wet grinding.
Do not use the power tool for cutting or roughing or polish-
ing. Do not use it together with wire brushes. Do not treat
asbestos containing materials with this power tool.
GB 13