General Safety Instructions; Work Area; Electrical Safety; Personal Safety - EINHELL PS-PS 750 Laser Bedienungsanleitung

Anleitung PS-PS 750 Laser_SPK1
Thank you for buying this jigsaw.
Your new jigsaw is easy to use and highly versatile –
an indispensable tool for all DIY enthusiasts.
This tool complies with the requirements of the
Equipment Safety Law and the relevant standards.
When using electrical equipment, a few safety pre-
cautions must be observed to avoid injuries and dam-
age. Please read the complete operating manual with
due care. Retain this manual in a safe place, so that
the information is available at all times. If you give the
equipment to any other person, hand over this oper-
ating manual as well.
We accept no liability for damage or accidents which
arise due to non-observance of these instructions.
We hope that you enjoy using your jigsaw.
1. SCOPE OF USE
This jigsaw can be used to cut wood, rubber, ceram-
ic, plastic and metal on a firm surface.
It can cut out pieces when used in soft materials. The
miter angle of the tool is 45° on both sides.

2. GENERAL SAFETY INSTRUCTIONS

CAUTION! Read the instructions in full.
Any errors made in following the instructions set out
below may result in an electric shock, fire and/or seri-
ous injury.
The term "electric tool" used below refers to electric
tools operated from the mains power supply (with a
power cable).
Keep these regulations in a safe place!

2.1 WORK AREA

Keep your work area clean and tidy.
Untidy and unlit work areas can result in acci-
dents.
Do not use this tool in an area where there is
a risk of explosion and where there are
inflammable liquids, gases or dust.
Electric tools generate sparks that can ignite dust
or vapors.
Keep children and other people away from
the electric tool whilst you are using it.
If you are distracted you may lose control of the
tool.
23.08.2005 10:23 Uhr Seite 13

2.2 ELECTRICAL SAFETY

The plug on the tool must fit into the socket.
The socket must not be modified in any way.
Do not use adapters with tools that must be
earthed.
Unmodified plugs and matching sockets will
reduce the risk of an electric shock.
Avoid body contact with earthed surfaces
such as pipes, heating systems, stoves and
refrigerators.
There is an increase risk of suffering an electric
shock if your body is earthed.
Keep the tool out of the rain and away from
moisture.
The ingress of water into an electric tool increa-
ses the risk of an electric shock.
Do not use the cable for a purpose for which
it is not designed, for example to carry the
tool, hang it up or to pull the plug out of the
socket. Keep the cable away from heat, oil,
sharp edges or moving parts of the tool.
Cables that are damaged or caught in machinery
increase the risk of an electric shock.
If you use an electric tool outdoors, use only
extension cables that are approved for outdo-
ors use.
The use of an extension cable that is approved
for outdoors use reduces the risk of an electric
shock.
Connect the electric tool to the mains power
supply (230V~, 50Hz) via a socket-outlet with
earthing contact with maximum 16A protec-
tion.
We recommend that you fit a residual-current
circuit-breaker (RCCB) with a maximum nomi-
nal tripping current of 30 mA. Seek the advice
of your electrician.

2.3 PERSONAL SAFETY

Be careful, watch what you are doing and use
an electric tool sensibly. Do not use the tool if
you are tired or under the influence of drugs,
alcohol or medication.
A moment of inattention when using the electric
tool can result in serious injuries.
Wear personal safety equipment and always
wear safety goggles.
Wearing personal safety equipment such as dust
masks, non-slip safety shoes, a helmet or ear
plugs, depending on the type and application of
the tool, reduces the risk of injury.
GB
13