Safety Information - Scheppach 4903303924 Originalbetriebsanleitung

DE GB FR CZ
• Catapulting parts out of damaged grinding
wheels.
• Catapulting of workpieces and parts of workpi-
eces.
• Damage to hearing if essential ear-muffs are not
used.
• Harmful emissions of wood dust when used in
closed rooms.
• The rotating parts of the device cannot be cov-
ered for functional reasons. Therefore you must
exercise care and hold the workpiece firmly to
prevent it slipping which could result in your
hands coming into contact with the grinding/
sanding belt.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not the
manufacturer will be liable for any damage or injuries
of any kind resulting from such misuse.
Please note that our equipment has not been desig-
ned for use in commercial, trade or industrial appli-
cations. Our warranty will be voided if the equipment
is used in commercial, trade or industrial businesses
or for equivalent purposes.

5. Safety information

m Caution!
Read all safety regulations and instructions. Any
errors made in following the safety regulations and
instructions may result in an electric shock, fire and/
or serious injury. Keep all safety regulations and
instructions in a safe place for future use.
m Warning! To protect against electric shock, injury
and fire the following basic safety precautions must
be observed when using power tools.
Read and follow these instructions before using the
equipment and keep the safety information in a safe
place.
1. Keep work area clean
Cluttered areas and benches invite injuries.
2. Consider work area environment
Don't expose power tools to rain. Don't use
power tools in damp or wet locations. Keep
work area well lit. Don't use power tools in
presence of flammable liquids or gases.
3. Guard against electric shock
Prevent body contact with grounded surfaces
(e.g. pipes, radiators, ranges refrigerators).
4. Keep children away
Do not allow other persons to touch the
equipment or cable, keep them away from
your work area.
5. Store idle tools
When not is use, tools should be stored in dry,
high, or locked-up place, out of the reach of
children.
6. Don't force tool
It will do the job better and safer at the rate for
which it was intended.
7. Use right tool
Don't force small tools or attachments to do the
job of heavy duty tool. Don't use tools for purpo-
18 / 136
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
SK DK ES FIN IT NL PL PT SE
ses not intended.
8. Dress properly
Do not wear loose clothing or jewellery.
They can be caught in moving parts. Rubber
gloves and non-skid footwear are recom-
mended when working outdoors. Wear
protective hair covering to contain long hair.
9. Use safety glasses
Also use face or dust mask if cutting operati-
on is dusty.
10. Don't abuse cord
Never carry tool by cord or yank it to disconnect
it from receptacle. Keep cord from heat, oil and
sharp edges.
11. Secure work
Use clamps or a vice to hold work. It's safer
than using your hand and it frees both hands
to operate tool.
12. Don't overreach
Keep proper footing and balance at all times.
13. Maintain tools with care
Keep tools sharp and clean for better and
safer performance. Follow instructions for lu-
bricating and changing accessories. Inspect
tool cords periodically and, if damaged,
have repaired by authorized service facility.
Inspect extension cords periodically and
replace if damaged. Keep handles dry, clean
and free from oil and grease.
14. Disconnect tools
When not in use, before servicing, and when
changing accessories.
15. Remove adjusting keys and wrenches
Form the habit of checking to see that keys
and adjusting wrenches are removed from
tool before turning it on.
16. Avoid unintentional starting
Don't carry plugged-in tool with finger on
switch. Be sure switch is off when plugging
in.
17. Outdoor use extension cords
When tool is used outdoors, use only exten-
sion cords intended for use outdoors and so
marked.
18. Stay alert
Watch what you are doing. Use common
sense. Do not operate tool when you are
tired.
19. Check damaged parts
Before further use of the tool, a guard or
other part that is damaged should be care-
fully checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, binding
of moving parts, breakage of parts, moun-
ting, and any other conditions that may
affect its operation. A guard or other part that
is damaged should be properly repaired or
replaced by an authorized service-center
unless otherwise indicated elsewhere in
this instructions manual. Have defective
switches replaced by an authorized service-
center. Do not use tool if switch does not
SI NO