Using The Serial Communication - JVC DT-V9L5 Bedienungsanleitung

External Control (cont.)
<Functions controlled by the MAKE/TRIGGER system>
Display
– – – No function
Tally lamp color selection*
Tally Color
Tally lamp lighting method selection
Tally Type
Light the left half of the tally lamp in red*
Tally-L(R)
Light the right half of the tally lamp in green*
Tally-R(G)
Changes the input to "SDI 1"
SDI-1
Changes the input to "SDI 2"
SDI-2
Changes the input to "HDMI"
HDMI
Changes the input to "VIDEO/COMPO."
Video/Component
The marker indication
Marker
The center marker indication
Center Marker
Indication of the area of the specified aspect ratio
Frame
Selects the items of "Marker"*
Marker Select
Changes the aspect ratio
Manual Aspect
Displays in 1:1 mode
1:1
Status display*
Status
Audio level meter display
Level Meter
Time code display
Time Code
☞ "Source ID" in "Information" on page 20
Source ID
Color off
Color Off
Screens check
Screens Check
Change a mode according to a input picture
I/P Mode
Muting on/off
Muting
Change the intensity of the button lamps
Dimmer
Wave form display
Wave Form
Vector scope display
Vector Scope
Histogram display
Histogram
Adjusts the picture to be suitable for a bright place
Dynamic
Can be controlled when "Tally Type" ("Set-Up Menu" → "Function Setting" → "Tally Setting") is set to "Normal".
* 1
Can be controlled when "Tally Type" ("Set-Up Menu" → "Function Setting" → "Tally Setting") is set to "Half".
* 2
* Selects which functions in "Marker" are activated, non-"R-" items or "R-" items. (☞ "Marker" on page 15)
3
* 4 Displays the information shown when INPUT SELECT button of the current input is pressed. (☞ "On the Status Display" on page 12) While controlling
with the MAKE system, the information is displayed only at the moment of short-circuiting.
* While controlling with the MAKE system, the level meter is switched between displayed (short-circuiting) and hidden (opening). When "Level Meter
5
Display" is set to "Off," the level meter is not displayed ("No Effect" appears).
While controlling with the TRIGGER system, the pattern of the audio channel display is switched.
* 6 While controlling with the MAKE system, the available set-up options will be the setting value currently selected in "Source ID" ("On" or "Auto" [short-
circuiting]) and "Off" (opening). While controlling with the TRIGGER system, uses the same set-up option as those in the Set-Up Menu. (☞ "Source ID"
in "Information" on page 20)
* 7 While controlling with the MAKE system, the screen is switched between normal screen (opening) and blue screen (short-circuiting). While
controlling with the TRIGGER system, the screen changes in the same way as when pressing SCR. CHK. button (☞ 7 on page 10).
* Must be controlled with the TRIGGER system. The mode is switched between "Normal" and "Cinema" (This function cannot be controlled with the
8
MAKE system).
●
You cannot assign the same function to different pin terminals.
●
The TRIGGER system switches each function by short-circuiting the pin terminal for about 1 second and opening it.

Using the serial communication

You can control the monitor from a personal computer etc. via the RS-232C terminal.
* Consult your dealer for the details of the external control specification.
<Communication specifications>
Input terminal
RS-232C A straight cable with a D-sub 9-pin
connector (male for the monitor,
female for the personal computer etc.)
<Specifications of the RS-232C terminal>
Pin No.
1
2
3
4
5
6
This is a female 7
terminal. 8
9
●
The 7th terminal and the 8th terminal are connected.
24
Functions to be controlled
1
3
4
Cable Terminal specification
☞ See below
Signal
NC
RXD
TXD
NC
GND
NC
RTS
CTS
NC
Opening
2
2
Non-"R-" items
Baud Rate: 4800 bps
Data Bits: 8 bits
Parity: No parity
Short-circuiting
—
Green
Whole One half at a time
On
On
Invalid
Invalid
Invalid
Invalid
Off
Off
Off
"R-" items
4:3
Off
☞ "On the Status Display" on page 12
*
5
Off
*
6
Color Monochrome
*
7
*
8
Off
Normal
Off
Off
Off
Invalid
Communication specifications
Stop Bits: 1 bit
Flow Control: No control
Communication Code: ASCII Code
—
Red
Off
Off
Valid
Valid
Valid
Valid
On
On
On
16:9
On
On
On
Dark
On
On
On
Valid