Pepperl+Fuchs VBG-PB-K5-R4-DMD Handbuch Seite 5

9.3.2.6 Parameterwert schreiben (WRITE_P: Write_Parameter) .................................. 50
9.3.2.7 Parameterwert lesen (READ_PI: Read_Parameter) ......................................... 50
9.3.2.8 Ist-Parameterwerte projektieren (STORE_PI: Store_Actual_Parameter) .......... 51
9.3.2.9 Konfigurationsdaten projektieren (SET_PCD: Set_Permanent_Configuration) 51
9.3.2.10 Projektierte Konfigurationsdaten lesen (GET_PCD:
Get_Permanent_Configuration) ......................................................................... 52
9.3.2.11 Ist-Konfigurationsdaten projektieren (STORE_CDI:
Store_Actual_Configuration) ............................................................................. 53
9.3.2.12 Ist-Konfigurationsdaten lesen (READ_CDI: Read_Actual_Configuration) ........ 53
9.3.2.13 Erweiterte LPS projektieren (SET_LPS) ............................................................ 54
9.3.2.14 LPS lesen (GET_LPS) ....................................................................................... 54
9.3.2.15 LAS lesen (GET_LAS) ....................................................................................... 55
9.3.2.16 LDS lesen (GET_LDS) ...................................................................................... 56
9.3.2.17 Flags lesen (GET_FLAGS) ................................................................................ 56
9.3.2.18 Betriebsmodus setzen (SET_OP_MODE: Set_Operation_Mode) .................... 58
9.3.2.19 Offline-Modus setzen (SET_OFFLINE) ............................................................. 59
9.3.2.20 SET_DATA_EX ................................................................................................. 60
9.3.2.21 AS-i-Slave-Adresse ändern (SLAVE_ADDR: Change_Slave_Address) ........... 60
9.3.2.22 Automatisches Adressieren wählen (SET_AAE) ............................................... 61
9.3.2.23 Peripheriefehlerliste lesen (GET_LPF) .............................................................. 61
9.3.2.24 Extended_ID-Code_1 schreiben (WRITE_XID1:
Write_Extended_ID-Code_1) ............................................................................ 62
9.3.2.25 Read 1 7.3-Slave in Data (RD_7X_IN) .............................................................. 62
9.3.2.26 Write 1 7.3-Slave out Data (WR_7X_OUT) ....................................................... 63
9.3.2.27 Read 1 7.3-Slave out.Data (RD_7X_OUT) ........................................................ 63
9.3.2.28 Read 4 7.3-Slave in.Data (RD_7X_IN_X) ......................................................... 64
9.3.2.29 Write 4 7.3-Slave out.Data (WR_7X_OUT_X) ................................................... 64
9.3.2.30 Read 4 7.3-Slave out.Data (RD_7X_OUT_X) ................................................... 65
9.3.2.31 Lesen der Ausgangsdaten (READ_ODI) ........................................................... 65
9.3.2.32 WR_74_PARAM ................................................................................................ 66
9.3.2.33 RD_74_PARAM ................................................................................................. 66
9.3.2.34 RD_74_ID .......................................................................................................... 67
9.3.2.35 RD_74_DIAG ..................................................................................................... 68
9.3.2.36 Listen und Flags lesen (Get_LPS, Get_LAS, Get_LDS, Get_Flags)
(GET_LISTS) ..................................................................................................... 68
9.3.2.37 LCS lesen (GET_LCS) ...................................................................................... 70
9.3.2.38 Liste der Off-line Slaves lesen (GET_LOS) ....................................................... 70
9.3.2.39 SET_LOS .......................................................................................................... 71
9.3.2.40 Get transm.err.counters (GET_TECA) .............................................................. 72
9.3.2.41 Get transm.err.counters (GET_TECB) .............................................................. 73
9.3.2.42 Get transm.err.counters (GET_TEC_X) ............................................................ 73
9.3.2.43 EXT_DIAG ......................................................................................................... 74
9.3.2.44 BUTTONS ......................................................................................................... 74
9.3.2.45 RD_EXT_DIAG .................................................................................................. 75
9.3.2.46 INVERTER ........................................................................................................ 76
9.3.2.47 FP_PARAM ....................................................................................................... 76
9.3.2.48 FP_DATA .......................................................................................................... 77
9.3.3 Funktionale Profile ............................................................................................. 77
9.3.3.1 „Safety at Work"-Liste 1 ..................................................................................... 77
Zumutbare Änderungen aufgrund technischer Verbesserungen vorbehalten.
Pepperl+Fuchs GmbH · 68301 Mannheim · Telefon (06 21) 7 76-11 11 · Telefax (06 21) 7 76 27-11 11 · Internet http://www.pepperl-fuchs.com
AS-i/PROFIBUS-Gateway
Inhaltsverzeichnis
Copyright Pepperl+Fuchs, Printed in Germany
3