Scheppach HMS850 Originalbetriebsanleitung Seite 21

7 Use the right tool
- Do not force small tools to do the job of a
heavy duty tool.
- Do not use tools for purposes not intended;
or example do not use circular saws to cut
tree limbs or logs.
8 Dress properly
- Do not wear loose clothing or jewellery, they
can be caught in moving parts.
- Non-skid footwear is recommended when
working outdoors.
- Wear protective hair covering to contain
long hair.
9 Use protective equipment
- Use safety glasses.
- Use face or dust mask if working operations
create dust.
10 Connect dust extraction equipment
- lf the tool is provided for the connection of
dust extraction and collecting equipment,
ensure these are connected and properly
used.
11 Do not abuse the cord
- Never yank the cord to disconnect it from
the socket. Keep the cord away from heat,
oil and sharp edges.
12 Secure work
- Where possible use clamps or a vice to hold
the work.
lt is safer than using your hand.
13 Do not overreach
- Keep proper footing and balance at all
times.
14 Maintain tools with care
- Keep cutting tools sharp and clean for better
and safer performance.
- Follow instruction for lubricating and chang-
ing accessories.
- lnspect tool cords periodically and if dam-
aged have them repaired by an authorized
service facility.
- lnspect extension cords periodically and re-
place if damaged.
- Keep handles dry, clean and free from oil
and grease.
15 Disconnect tools
- When not in use, before servicing and when
changing accessories such as blades, bits
and cutters, disconnect tools from the power
supply.
If the planer shaft blocked when working by
excessive feed force or clamping the work
piece, turn off the device and disconnect it
from the mains plug. Remove the workpiece
and make sure that the planer shaft runs
freely. Turn the power on, and run the op-
eration again with reduced feed force.
16 Remove adjusting keys and wrenches
- Form the habit of checking to see that keys
and adjusting wrenches are removed from
the tool before turning it on.
17 Avoid unintentional starting
- Ensure switch is in "off' position when plug-
ging in.
18 Use outdoor extension leads
- When the tool is used outdoors, use only
extension cords intended for outdoor use
and so marked.
19 Stay alert
- Watch what you are doing, use common
sense and do not operate the tool when you
are tired.
20 Check damaged parts
- Before further use of tool, it should be care-
fully checked to determine that it will oper-
ate properly and perform its intended func-
tion.
- Check for alignment of moving parts, bind-
ing of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation.
- A guard or other part that is damaged
should be properly repaired or replaced by
an authorized service centre unless other-
wise indicated in this instruction manual.
- Have defective switches replaced by an au-
thorized service centre.
- Do not use the tool if the switch does not
turn it on and off.
21 WARNING!
- The use of any accessory or attachment
other than one recommended in this instruc-
tion manual may present a risk of personal
injury.
22 Have your tool repaired by a qualified person
- This electric tool complies with the relevant
safety rules. Repairs should only be carried
out by qualified persons using original spare
parts, otherwise this may result in consider-
able danger to the user.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
SPECIAL SAFETY INSTRUCTIONS
• Do not use blunt knives. Risk of kick-back.
• The cutter block must be fully covered.
• Use a push stick to plane any short workpieces.
• Take additional safety precautions if you are plan-
ing any narrow workpieces. It may be necessary
to use lateral pressure equipment and springload-
ed covers to ensure that you can work in safety.
• The machine is not suitable for cutting rebates.
• The anti-kick safeguard and the infeed roller must
be inspected at regular intervals.
GB 21