Politik der ständigen Entwicklung und Aktualisierung des Produkts und kann ohne Vorankündigung Änderungen vornehmen. Alle Maße dieser Bedienungsanleitung sind in mm angegeben. ACHTUNG: Die Erstinbetriebnahme des Gerätes darf nur durch autorisierte Austroflamm Servicepartner erfolgen. Ihr Heizgerät ist nicht zur Verwendung als Leiter oder Standgerüst geeignet.
1. Zubehör aus Pellettank entfernen, Pellets einfüllen (voll) und Tankdeckel schließen. 2. Netzkabel einstecken. 3. Kippschalter auf der Rückseite des Pelletofens auf I stellen. 4. Am Bedienfeld erscheint das Austroflamm Logo. Nach wenigen Sekunden wechselt die Anzeige auf diese Ansicht: 5. Wenn gewünscht, Anzeigesprache ändern (das Symbol gibt an, welche Icons auf dem Bedienfeld berührt oder gehalten werden müssen):...
Tabelle 1 - Bezeichnung der Symbole HINWEIS: Menüs werden für Ben, Percy light und Polly light nach links bzw. rechts durchgeblättert ( ). Menüs für Percy und Polly 2.0 werden aber von oben nach unten durchgeblättert ( 4.3.
deutsch Ändern Sie die Solltemperatur, durch tippen auf und/oder . Die Änderungen werden sofort gespeichert. 4.5. Den Pelletofen einschalten 4 . 5 .1 . A m B e d ienf el d Berühren Sie den Bildschirm (falls noch im Ruhemodus), um den Ruhemodus zu verlassen. Wenn sich die Anzeige derzeit nicht im Ruhemodus befindet, überspringen Sie diesen Schritt.
deutsch 4.6. Leistungsstufe ändern/auswählen Am Bedienfeld können Sie 5 verschiedene Leistungsstufen einstellen. Berühren Sie den Bildschirm (falls noch im Ruhemodus), um den Ruhemodus zu verlassen. Wenn sich die Anzeige derzeit nicht im Ruhemodus befindet, überspringen Sie diesen Schritt. Erhöhen/Verringern Sie die Leistungsstufe durch tippen auf oder .
Seite 9
deutsch Tabelle 3 - Korrekter Gebrauch von Wochentimer (Beispiel) Um Wochentimer einzustellen, gehen Sie folgendermaßen vor: Berühren Sie den Bildschirm (falls noch im Ruhemodus), um den Ruhemodus zu verlassen. Wenn sich die Anzeige derzeit nicht im Ruhemodus befindet, überspringen Sie diesen Schritt. ''Neuen Timerzeit'' Wählen Sie den Tag / die Tage des Zeitintervalls, das angezeigt werden soll, indem Sie auf die Initiale tippen (Mo = Montag, Di = Dienstag, Mi = Mittwoch, Do = Donnerstag, Fr = Freitag, Sa =...
Solltemperatur ist, dann wird der Pelletofen erst dann eingeschaltet werden, wenn die Temperatur unter den Sollwert gesunken ist. HINWEIS: Ben, Polly light und Percy light verfügen über keinen Kipprost. Die Funktion „Wochentimer“ ist daher nur eingeschränkt nutzbar. Sobald der Brenntopf mit Aschekuchen am Boden über das Zündloch hinaus bedeckt ist, kann die automatische Zündung nicht mehr...
deutsch 4.11. Brennstoffautonomie nach dem Befüllen des Brennstofftanks zurücksetzen Nach dem Befüllen des Pellettanks ist es notwendig, die Brennstoffautonomie zurückzusetzen. Um die Brennstoffautonomie zurückzusetzen, gehen Sie folgendermaßen vor: Berühren Sie den Bildschirm (falls noch im Ruhemodus), um den Ruhemodus zu verlassen. Wenn sich die Anzeige derzeit nicht im Ruhemodus befindet, überspringen Sie diesen Schritt.
deutsch Stellen Sie die gewünschte aktive Display-Helligkeit ein, indem Sie auf Symbole und/oder neben der Bezeichnung ''Helligkeit aktiv'' tippen. Die Änderungen werden sofort gespeichert. HINWEIS: Wenn die automatische Helligkeitsanpassung aktiv ist, ist diese Option deaktiviert. 4 . 12 .3 . D ie D i sp lay- H e l l ig ke it i m R u hem o du s e ins t e l le n Sie können die Display-Helligkeit im Ruhemodus erhöhen oder verringern, um Energie zu sparen.
deutsch Berühren Sie den Bildschirm (falls noch im Ruhemodus), um den Ruhemodus zu verlassen. Wenn sich die Anzeige derzeit nicht im Ruhemodus befindet, überspringen Sie diesen Schritt. „Anzeigeoptionen“ 'Standby-Modus'' Aktivieren Sie die Info, die im Standbymodus angezeigt werden soll, indem Sie auf das Symbol ''On/Off'' tippen (Mehrfachauswahl möglich).
deutsch 4.18. Funktion „Display reinigen“ Das Bedienfeld enthält eine Funktion, die die Anzeige für 30 Sekunden inaktiv macht. Dies ermöglicht Ihnen, das Display ohne das Auslösen von Funktionen zu reinigen. Berühren Sie den Bildschirm (falls derzeit im Ruhemodus), um den Ruhemodus zu verlassen. Wenn sich die Anzeige derzeit nicht im Ruhemodus befindet, überspringen Sie diesen Schritt.
deutsch 5. Alarme und Fehler Alarme werden am Bedienfeld gelb dargestellt, der Pelletofen kann weiter benutzt werden. Allerdings muss gegebenenfalls die Alarmmeldung auf dem gelben Bildschirm mit „X“ bestätigt werden. Fehler werden dagegen rot angezeigt, der Pelletofen kann nur noch eingeschränkt oder gar nicht betrieben werden.
deutsch 5.1. Alarme zurücksetzen Im Falle eines Alarms zeigt der Bildschirm die gelbe Meldung mit der Alarmbeschreibung (siehe Beispiel unten). Um den Alarm-Bildschirm zu schließen, tippen Sie auf . Das Schließen des Alarm-Bildschirms setzt den Alarm nicht zurück. Nach dem Schließen des Alarm-Bildschirms mit ist der Alarm- Code immer noch in der oberen linken Ecke des Hauptbildschirms als auch auf allen Ruhemodus- Bildschirmen vorhanden (siehe Beispiel unten).
Wartung ist durch Servicetechniker auszuführen. Reinigung der Sichtscheibe Ca. 15 Betriebsstunden, bei Bedarf Sichtprüfung Brenntopf und Rost, anhaftende Ablagerung entfernen Ben. Polly light, Percy light: nach jedem Abschalten, sonstige Modelle ca. 2 - 3 Tage Entleerung der Aschebox und Reinigung des Brennraumes wöchentlich, bei Bedarf...
Die Modelle Polly 2.0 und Percy sind serienmäßig mit einer WLan Box ausgerüstet, für die Modelle Ben, Percy light und Polly light kann die WLan Box als Zubehör nachgerüstet werden. Die WLan Box erlaubt es, Ihren Pelletofen in Ihr bestehendes WLan (wireless lan / Drahtlosnetzwerk) einzubinden und den Ofen in der Folge mittels Smartphone (iOS und Android) zu überwachen und...
9. Garantie Für Ihren AUSTROFLAMM-Pelletofen garantieren wir für die einwandfreie Funktion des Korpus 6 Jahre, aller weiteren Bauteile aus Stahl und Guss 2 Jahre ab dem Erstverkaufsdatum. Stahl- und Gussteile, die während der Garantiezeit Material- und / oder Verarbeitungsmängel aufweisen, werden gegen Neuteile ersetzt.
Toutes les dimensions de ce manuel d'utilisation sont en mm. ATTENTION : La première mise en service de l’appareil ne doit être réalisée que par un partenaire de service Austroflamm. Votre chauffage ne doit pas servir d’échelle ou d’escabeau. Tenez compte du fait que les surfaces du poêle à granulés deviennent très chaudes pendant son fonctionnement.
2. Branchez le câble réseau. 3. Mettez l’interrupteur au dos du poêle à granulés sur I. 4. Le panneau de commande affiche le logo d’Austroflamm. Après quelques secondes s’affiche l’écran suivant : 5. Vous pouvez, si vous le voulez, modifier la langue des menus (le symbole indique les icônes à...
Définir le verrouillage d'écran sur LOW Effleurer Fermer le menu Effleurer Retourner au menu précédent Effleurer Écran de sous-menu précédent (Ben, Percy light, Effleurer Polly light) Écran de sous-menu suivant Effleurer Écran de sous-menu suivant (Percy, Polly 2.0) Informations sur le sous-menu sélectionné...
Indique les icônes à effleurer ou toucher sans relâcher Tableau 5 - Désignation des symboles REMARQUE : Dans le panneau de commande des appareils Ben, Percy light et Polly light, les menus défilent horizontalement ( ). Dans le panneau de commande des appareils Percy et Polly 2.0, les menus défilent verticalement (...
français Réglez la température nominale en appuyant sur et/ou . Les modifications effectuées sont enregistrées immédiatement. 4 .5. Mettre le poêle à granulés en marche 1 .1 .1 . Su r le pann ea u de co mmand e Si l’appareil est en mode Veille, appuyez sur l’écran pour le quitter. Sinon, passez à l’étape suivante. Appuyez sans relâcher sur (voir ci-dessous) : Les écrans suivants sont affichés de la façon suivante :...
français 4.6. Sélectionner/Modifier les niveaux de puissance Le panneau de commande sert à sélectionner 5 niveaux de puissance différents. Si l’appareil est en mode Veille, appuyez sur l’écran pour le quitter. Sinon, passez à l’étape suivante. Réglez le niveau de puissance en appuyant sur .
Seite 30
français Tableau 7 - Utilisation correcte du chronomètre hebdomadaire (exemple) Procédure de réglage du chronomètre hebdomadaire : Si l’appareil est en mode Veille, appuyez sur l’écran pour le quitter. Sinon, passez à l’étape suivante. Nouvelle période de chronomètre Sélectionnez le ou les jours de la période à afficher en appuyant sur leur abréviation (Lun = lundi, Mar = mardi, Mer = mercredi, Jeu = jeudi, Ven = vendredi, Sam = samedi, Dim = dimanche).
REMARQUE : Ben, Polly light et Percy light n’ont pas de grille basculante. La fonction Chronomètre hebdomadaire ne peut donc être utilisée que de façon limitée. Dès que les cendres dans le braséro dépassent le trou d’allumage, l’allumage automatique est désactivé. Pour que votre poêle à...
français Si l’appareil est en mode Veille, appuyez sur l’écran pour le quitter. Sinon, passez à l’étape suivante. L’écran affiche les informations suivantes : Appuyez sur PLEIN après avoir rempli le réservoir de combustible. Appuyez sur OK pour enregistrer vos paramètres. La barre de combustible est maintenant pleine : 4.12.
français Options d’affichage Luminosité de l’écran Appuyez sur les symboles et/ou à côté du mot Lumin. stand-by pour régler la luminosité de l’écran en mode Veille souhaitée. Les modifications effectuées sont enregistrées immédiatement. REMARQUE : Cette option est désactivée lorsque l’adaptation automatique de la luminosité est activée.
français Volume Appuyez sur les symboles et/ou pour désactiver ou régler le volume du haut-parleur. 4.16. Alimentation en granulés manuelle Lorsque vous utilisez le poêle à granulés pour la première fois ou après le nettoyage de son puits, l’alimenteur à granulés est complètement vide. Avant la mise en service, remplissez l’alimenteur avec la fonction Alimentation manuelle.
Seite 35
français Si l’appareil est en mode Veille, appuyez sur l’écran pour le quitter. Sinon, passez à l’étape suivante. ) ) ) Langue Appuyez sur la langue de votre choix. La modification est immédiatement enregistrée et le panneau de commande redémarre.
français 5. Alarmes et Défauts Les alarmes sont affichées en jaune sur le panneau de commande, vous pouvez continuer à utiliser le poêle à granulés. Cependant, vous devez dans ce cas confirmer le message d'alarme avec X sur l'écran jaune. Les défauts sont eux affichés en rouge, vous ne pouvez alors plus ou de façon limitée utiliser le poêle à...
français 5.1. Réinitialiser une alarme En cas d’alarme, l’écran affiche un message en jaune avec sa description (voir exemple ci- dessous). Appuyez sur pour quitter l’écran des alarmes. Ceci ne réinitialise pas l’alarme. Une fois fermé l’écran des alarmes avec , le code de l’alarme est toujours affiché...
Nettoyage du hublot Après env. 15 heures de service, au besoin Contrôler le braséro et la grille de combustion, éliminer les dépôts Ben, Polly light, Percy light : Après chaque arrêt Autres modèles : env. tous les 2 - 3 jours Vider le bac à...
Les modèles Polly 2.0 et Percy sont livrés en série avec une box Wi-Fi, en option pour les modèles Ben, Polly light et Percy light. La box Wi-Fi vous permet d’intégrer votre poêle à granulés au réseau de communication sans fil de votre domicile pour le surveiller et contrôler avec votre smartphones (iOS et Android).
À partir de la date de l’achat initial, nous appliquons une garantie de 6 ans sur le fonctionnement correct de votre poêle à granulés AUSTROFLAMM et une garantie de 2 ans sur les composants/pièces en acier et en fonte. Les composants/pièces en acier et en fonte s’avérant défectueux pendant la période de garantie seront remplacés par des composants neufs.
Tutte le misure riportate nelle istruzioni per l'uso sono indicate in mm. ATTENZIONE: La prima messa in funzione dell’apparecchio deve essere effettuata solo dal servizio di assistenza Austroflamm. La stufa non è adatta per essere utilizzata come scala o per fungere da impalcatura.
2. Collegare il cavo di rete. 3. Posizionare il commutatore a levetta sul lato posteriore della stufa a pellet su I. 4. Sul pannello comandi appare il logo Austroflamm. Dopo pochi secondi la visualizzazione passa a questa schermata: 5. Se lo si desidera, cambiare la lingua visualizzata (il simbolo ) indica quali icone sul pannello...
Impostare il blocco dello schermo su LOW Toccare Chiudere il menu Toccare Scorrere all’indietro Toccare Pagina del sottomenu precedente (Ben, Percy light, Toccare Polly light) Pagina del sottomenu successiva Toccare Pagina del sottomenu successiva (Percy, Polly 2.0) Informazioni sul sottomenu selezionato Toccare Monitorare / resettare l’autonomia di combustibile...
Tabella 9 - Denominazione dei simboli NOTA: Per Ben, Percy light e Polly, i menu vengono sfogliati verso sinistra e/o verso destra ( ). I menu per Percy e Polly 2.0 vengono però sfogliati dall’alto verso il basso ( 4.3.
italiano 4.5. Accendere la stufa a pellet 4 .5 .1 . Su l pa nne llo co ma ndi Toccare lo schermo (se si trova ancora in modalità di riposo) per uscire dalla modalità di riposo. Se la visualizzazione al momento non si trova in modalità di riposo, saltare questo passo. Tenere premuto (vedere in basso.): Le seguenti schermate vengono visualizzate nel modo seguente:...
italiano Toccare lo schermo (se si trova ancora in modalità di riposo) per uscire dalla modalità di riposo. Se la visualizzazione al momento non si trova in modalità di riposo, saltare questo passo. Aumentare/ridurre il livello di potenza toccando . Le modifiche vengono salvate immediatamente.
Seite 51
italiano Tabella 11 - uso corretto del timer settimanale (esempio) Per impostare il timer settimanale, procedere nel modo seguente: Toccare lo schermo (se si trova ancora in modalità di riposo) per uscire dalla modalità di riposo. Se la visualizzazione al momento non si trova in modalità di riposo, saltare questo passo. ) ) ) ) “Aggiungi nuovo timer”...
NOTA: Ben, Polly light e Percy light non sono dotati di una griglia ribaltabile. Pertanto la funzione “Timer settimanale” è utilizzabile solo in modo limitato. Non appena il braciere con agglomerato di cenere sul fondo è coperto fino a oltre il foro di accensione, non è più possibile effettuare l’accensione automatica.
italiano Per resettare l’autonomia di combustibile la qualità del combustibile, procedere nel modo seguente: toccare lo schermo (se si trova ancora in modalità di riposo) per uscire dalla modalità di riposo. Se la visualizzazione al momento non si trova in modalità di riposo, saltare questo passo. Viene visualizzata la seguente schermata: Toccare PIENO dopo aver rabboccato il combustibile.
italiano 4 .12 .3 . Imp ost ar e la lu mino sità de l d is pl ay i n m od al it à di r ipo s o È possibile aumentare o ridurre la luminosità del display in modalità di riposo al fine di risparmiare energia.
italiano 4.15. Impostare il volume degli altoparlanti È possibile impostare il volume degli altoparlanti integrati o disattivarli completamente. Per impostare il volume desiderato degli altoparlanti, procedere nel modo seguente: toccare lo schermo (se si trova ancora in modalità di riposo) per uscire dalla modalità di riposo. Se la visualizzazione al momento non si trova in modalità...
italiano NOTA: Questa funzione è disattivata durante l’esercizio della stufa a pellet. 4.19. Impostare la lingua Per impostare la lingua desiderata, procedere nel modo seguente: toccare lo schermo (se al momento si trova in modalità di riposo) per uscire dalla modalità di riposo.
italiano 5. Allarmi ed errori Sul pannello comandi gli allarmi vengono rappresentati in giallo: è possibile continuare a usare la stufa a pellet. Tuttavia all’occorrenza è necessario confermare il messaggio di allarme sullo schermo giallo con “X”. Per contro, gli errori vengono visualizzati in rosso: la stufa a pellet può essere fatta funzionare solo limitatamente o non può...
italiano 5.1. Resettare gli allarmi In caso di allarme, la schermata mostra il messaggio giallo con la descrizione dell’allarme (vedere l’esempio in basso). Per chiudere la schermata di allarme, toccare . La chiusura della schermata di allarme non resetta l’allarme. Dopo la chiusura della schermata di allarme con , il codice di allarme è...
Pulizia del vetro di ispezione Circa 15 ore di esercizio, all’occorrenza Controllo visivo del braciere e della griglia, rimuovere i depositi incrostati Ben. Polly light, Percy light: dopo ogni spegnimento, altri modelli circa 2 - 3 giorni Svuotamento del cassetto raccoglicenere e pulizia della camera di...
I modelli Polly 2.0 e Percy sono dotati di serie di una WLan box, disponibile come accessorio per i modelli Ben, Percy light e Polly light. La WLan box consente di integrare la stufa a pellet nella propria WLan esistente (wireless lan / rete wireless) e in seguito di monitorare e controllare la stufa tramite smartphone (iOS e Android).
9 . Garanzia Per la stufa a pellet AUSTROFLAMM garantiamo un funzionamento ineccepibile di 6 anni per il corpo della stufa e di 2 anni dalla data della prima vendita per tutti gli altri componenti in acciaio e in ghisa.
Italiano Dati tecnici 10.1. Ben 6,7 kW Potenza calorifica nominale (NWL) 2 kW Potenza calorifica a carico parziale 50 – 165 m³ Volume riscaldabile Rendimento di combustione 72,7 mg/Nm³ Contenuto di monossido di carbonio a potenza calorifica nom. 119,9 mg/Nm³...
english 10.2. Percy 8,6 kW Potenza calorifica nominale (NWL) 2,4 kW Potenza calorifica a carico parziale 50 – 240 m³ Volume riscaldabile Rendimento di combustione 90,20% Contenuto di monossido di carbonio a potenza 36,7 mg/Nm³ calorifica nominale 338 mg/Nm³ Contenuto di monossido di carbonio a carico parz. 208 °C Temperatura dei fumi a potenza calorifica nominale Temperatura dei fumi a TL (carico parziale)
Italiano 10.3. Polly 2.0 / Polly light Potenza calorifica nominale (NWL) 7,8 / 9 kW Potenza calorifica a carico parziale 2,4 / 2,7 kW Volume riscaldabile 50 – 240 m³ Rendimento di combustione 90,7 / 90% Contenuto di monossido di carbonio a potenza calorifica nom. 47 / 29 mg/Nm³...
Seite 65
Cleaning/servicing ....................78 Replacing the Battery of the Control Unit ............... 78 Wifi box & PelletControl ..................79 Guarantee ......................80 Technical Data ..................... 81 10.1. Ben ........................ 81 10.2. Percy ......................82 10.3. Polly 2.0 / Polly light ..................83...
All dimensions stated in these user instructions are in mm. ATTENTION: Only authorized Austroflamm service partners are allowed to carry out initial commissioning of the device. Your heating device is not suited for use as a ladder or support stand.
2. Plug in the mains cable. 3. Set the rocker switch on the back of the pellet stove to I. 4. The Austroflamm logo is displayed on the control panel. After a few seconds, the display changes to this view: 5.
Hold Set screen lock to HIGH Set screen lock to LOW Close menu Navigate back Previous sub-menu page (Ben, Percy light, Polly light) Next sub-menu page Next sub-menu page (Percy, Polly 2.0) Information about the selected sub-menu Monitor/reset fuel autonomy ON -->...
Table 13 - Designations of symbols NO T E : With Ben, Percy light and Polly light, you page through the menus to the left or to the right ( ). However, with Percy and Polly 2.0 you page through the menus from the top to the bottom 4.3.
english 4.5. Switching on the pellet stove 4 . 5 .1 . O n t h ec ont ro l pan e l T ap the screen (if it is still in idle mode) to leave idle mode. If the display is not currently in idle mode, skip this step.
english Tap the screen (if it is still in idle mode) to leave idle mode. If the display is not currently in idle mode, skip this step. to increase or decrease the power level. The system saves the changes immediately. NOTE: After starting the pellet stove, we recommend running it for at least 30 minutes at power level 5 / AUTO.
Seite 72
english Table 15 - Correct use of the week timer (example) To set the week timer, proceed as follows: Tap the screen (if it is still in idle mode) to leave idle mode. If the display is not currently in idle mode, skip this step.
NOTE: Ben, Polly light and Percy light do not have a tilting grate. This means that you can only use the “"Week timer” to a limited extent. Once ash cake covers the base of the burner bowl above the ignition hole, it is no longer possible to carry out automatic ignition. This means that you must empty the burner bowl in good time to be able to start your pellet stove reliably using the timer function.
english Tap the screen (if it is still in idle mode) to leave idle mode. If the display is not currently in idle mode, skip this step. The system displays the following: Tap FULL after you have topped up with fuel Tap ''OK'' to save your settings.
english Tap the screen (if it is still in idle mode) to leave idle mode. If the display is not currently in idle mode, skip this step. “Display options” “Display brightness” Set the desired display brightness in idle mode by tapping the and/or symbols next to the “Idle disp.
english Tap the screen (if it is still in idle mode) to leave idle mode. If the display is not currently in idle mode, skip this step. “Volume” Set the desired loudspeaker volume or switch it off altogether by tapping on the and/or symbols.
Seite 77
english Tap the screen (if it is currently in idle mode) to leave idle mode. If the display is not currently in idle mode, skip this step. ) ) ) “Language” Tap the language that you want to choose. The system saves the change immediately and the control panel restarts.
english 5. Alarms and errors The system displays alarms in yellow on the control panel and you can continue to use the pellet stove. However, you may need to acknowledge the alarm message on the yellow screen by means of an “X”. On the other hand, the system displays errors in red. This means that you can only operate the pellet stove to a limited extent or not at all.
english 5.1. Resetting alarms If there is an alarm, the system shows the message in yellow on the screen together with the alarm description (see the example below). To close the alarm screen, tap . Closing the alarm screen does not reset the alarm. After tapping to close the alarm screen, the alarm code is still present in the top left-hand corner of the main screen as well as on all the idle mode screens (see the example below).
Cleaning the viewing window Approximately 15 operating hours or if necessary Visual inspection of the burner bowl and grate, remove clinging deposits Ben, Polly light, Percy light: each time they have been switched off, other models approximately 2 - 3...
As-standard, models Polly 2.0 and Percy are fitted with a Wifi box; you can retrofit the Wifi box as an accessory for the Ben, Percy light and Polly light models. The Wifi box allows you to integrate your pellet stove into your existing wifi network and to monitor and control it using your smartphone (under iOS and Android).
9. Guarantee For your AUSTROFLAMM pellet stove, we guarantee the flawless function of the main structure for 6 years and for 2 years for all further components made of steel and cast iron, starting from the date of initial purchase. Parts made of steel or cast iron which have been proven to have material or workmanship defects shall be replaced by new parts.
Technical Data 10.1. Ben 6.7 kW Nominal thermal output (NWL) 2 kW Partial-load thermal output 50 - 165 m³ Space heating capacity Degree of effectivity 72.7 mg/Nm³ CO content at NWL 119.9 mg/Nm³ CO content at partial load Flue gas temperature at NWL 176 °C...
english 10.2. Percy 8.6 kW Nominal thermal output (NWL) 2.4 kW Partial-load thermal output 50 - 240 m³ Space heating capacity Degree of effectivity 90.20% CO content at NWL 36.7 mg/Nm³ CO content at partial load 338 mg/Nm³ Flue gas temperature at NWL 208 °C Flue gas temperature at TL (partial load) 90 °C...