Scheppach 5901407901 Originalbetriebsanleitung Seite 32

2. Press the arm (12) down lightly. Fasten the other
end of the saw blade (22) in the top saw blade
holder (27) (see fig. 9).
3. Fasten the saw blade (22) using the upper saw
blade clamping screw (28) (see fig. 10).
4. Tension the saw blade (22) with the tightening le-
ver (11) by pressing down on it again. Check the
tensioning of the saw blade (22). If the tension is
too low, you can increase it by turning it clockwise.
Before doing this, release the tightening lever (11)
again.
5. Re-insert the table inlay (26).
8.1.3 Removing the saw blade with pins
1. To remove the saw blade (22), remove the table
inlay (26) upwards.
2. First, release the tension by flipping the tension
lever (11) upwards. Continue reducing the tension
by turning anti-clockwise as required.
3. Press the arm (12) down lightly (see Fig. 9).
4. Remove the saw blade from the top and bottom
saw blade holder (27/30).
8.1.4 Inserting the saw blade with pins
The teeth of the saw blade must always point down-
wards.
1. Insert one end of the saw blade (22) through the
drilled hole in the table. Insert the pins of the saw
blade (22) into the corresponding recesses of the
top and bottom saw blade holder (27/30).
2. First, insert the saw blade (22) into the bottom saw
blade holder (30).
3. Press the arm (12) down lightly (see Fig. 9).
4. Check the position of the saw blade pins in the saw
blade holders (27/30).
5. Tension the saw blade (22) with the tightening le-
ver (11) by pressing down on it again. Check the
tensioning of the saw blade (22). If the tension is
too low, you can increase it by turning it clockwise.
Before doing this, release the tightening lever (11)
again.
6. Re-insert the table inlay (26).
NOTE
The left side features a storage box (9), which enables
you to stow replacement saw blades and the hexagon
wrench.
32 | GB
8.2 Checking the saw blade tension
WARNING
Check the blade tension regularly and after insert-
ing a saw blade.
Tension the saw blade after assembly by pressing
down on the tension lever (11).
If the blade tension is too low or too high, proceed as
follows:
• Fold the tension lever (11) upwards.
• Turn the tension lever (11) clockwise to increase the
tension and anti-clockwise to reduce it.
• Press the tension lever down again to engage the
setting.
If the tension is correct, the saw blade should produce
a light tone when it is plucked, like a string.
8.3 Fine adjustment of the angle scale
(Fig. 12; 12.1)
ATTENTION
Check the setting of the angle scale before working
with the device.
1. Loosen the locknut of the adjustment screw (37).
2. To set the saw table, use a 90° bracket (31, not in
the scope of delivery). Place this against the saw
table and the saw blade (fig. 12).
3. Adjust the adjustment screw (37) until the angle
between the saw blade (22) and the saw table (6)
is 90°.
4. Retighten the locknut of the adjustment screw (37).
5. Loosen the screw (32) and turn the pointer (33) to
the 0° marking.
6. Make a test cut. Check the angle on the workpiece
with a protractor. If necessary, readjust the pointer
(33).
8.4 Installing the blow-off device (Fig. 8)
1. Ensure that the saw blade guard (5) folded down.
2. Screw the blow-off device (1) clockwise onto the
holder (2) as described in fig. 8.
8.5 Installing the depressor (Fig. 6, 7)
NOTE:
Before assembling the depressor (24), the saw blade
pre-installed at the factory (22) must be removed (see
8.1.3).
www.scheppach.com