Scheppach LB5200BP Originalbetriebsanleitung Seite 25

• Always carry out a visual inspection before using of
the product. Check in particular:
– The throttle lever must move freely and should re-
turn to the neutral position independently and
quickly.
– The on/off switch must be easy to operate.
– All electrical cables such as spark plug cables and
the spark plug connector must be in perfect condi-
tion to avoid sparks. The spark plug connector
must be firmly seated on the spark plug.
– Keep the handle dry, clean and free of oil and
grease. Handles and guards must be undamaged.
– The fan must be undamaged.
– The collection bag must be undamaged.
• Before starting work, always remove any objects lying
on the ground that
– could be thrown when operating the product (when
using as a blower)
– could jam the vacuum tube (when using as a leaf
vacuum)
– could represent a hazard (stones, sticks, wire,
bones, etc.)
5.3 Operation
• Keep hands and feet away from the rotating parts.
• Do not run the combustion engine in closed rooms in
which hazardous carbon monoxide can collect.
• Do not fit any products or accessories to the product
that are not provided by or approved by the manufac-
turer.
• Keep your work area clean and well-lit. Cluttered or
dark areas invite accidents.
• Do not use a product that has a defective switch. Any
product that cannot be switched on or off is dangerous
and must be repaired.
• Never use the product:
– Without having mounted all accessories intended
for the respective use (when used as a leaf vacu-
um or blower)
– Whilst other persons, in particular children or ani-
mals, are nearby.
– In enclosed spaces, in an explosive environment,
where flammable liquids, gases or dusts may be
located.
• Always ensure that you have a safe and firm footing
so that you can control the product and maintain your
working posture even in the event of unexpected
movements.
– If possible, avoid working on wet or slippery
ground. Avoid working on uneven or steep ground
that does not guarantee the operator a safe work-
ing posture.
– Move slowly, do not run. Pay attention to the
ground conditions and any obstacles.
• Make sure the product is fully assembled before start-
ing it.
– Start the product at a distance of at least 3 m from
the fuel filling point.
– People should keep a safe distance of at least 15
metres from the work area.
– Do not point the silencer and thus the exhaust
gases at combustible materials.
• Do not make any modifications to the engine.
• Do not overload the product. Use the correct tool for
your application. The correct tool will do the job better
and safer at the rate for which it was designed.
• Make sure that the product does not come into con-
tact with foreign bodies or with foreign bodies and
dust that may be stirred up by the air.
• Never point the air stream at people or animals.
• Never insert objects into the openings of the product
and avoid sucking in large objects that could damage
the fan.
• Keep your hands away from the intake grille and the
air outlet during use and never block the fan.
• Stop the engine:
– When converting the product from a leaf vacuum
to a leaf blower.
– When you are leaving the product unattended.
– Before refuelling.
– When you move to a different working area.
• Stop the engine and disconnect the spark plug con-
nector:
– Before cleaning and maintenance work.
– If a foreign body is sucked in. Check the product
for damage before operating it again.
– If the product starts to produce unusual vibrations.
– When you are not using the product.
• Do not leave the product on leaves, dry grass or other
combustible material when the engine is hot. Fire
hazard!
• Do not work with the product in an explosive environ-
ment where flammable liquids, gases or dusts may be
located. The product creates sparks which may ignite
the dust or vapours.
• Warning! Do not work near open windows. Watch out
for children, pets and blow away foreign objects safe-
ly.
• Keep children and other people away while using the
product. Distractions may cause you to lose control of
the product.
• Avoid abnormal postures. Keep proper footing and
balance at all times. This enables better control of the
tool in unexpected situations.
• Stay alert, watch what you are doing and use common
sense when operating the tool. Do not use any tool
while you are tired or under the influence of drugs, al-
cohol or medication. A moment of carelessness when
using the tool can result in serious injuries.
• Prevent unintentional starting. Carrying tools with your
finger on the switch on invites accidents.
• Remove any adjusting tools or spanners before turn-
ing the tool on. A tool or spanner that is located in a
rotating device part may result in injuries.
www.scheppach.com GB | 25