Specific Safety Instructions - Ferm CSM1038 Übersetzung Der Originalbetriebsanleitung

EN
can dig into the top surface of the wood
causing the blade to climb out of the kerf and
jump back toward the operator.
• Kickback is the result of saw misuse and/or
incorrect operating procedures or conditions
and can be avoided by taking proper
precautions as given below.
a) Maintain a firm grip with both hands on the
saw and position your arms to resist kickback
forces. Position your body to either side of the
blade, but not in line with the blade. Kickback
could cause the saw to jump backwards,
but kickback forces can be controlled by the
operator, if proper precautions are taken.
b) When blade is binding, or when interrupting
a cut for any reason, release the trigger and
hold the saw motionless in the material until
the blade comes to a complete stop. Never
attempt to remove the saw from the work or
pull the saw backward while the blade is in
motion or kickback may occur. Investigate and
take corrective actions to eliminate the cause
of blade binding.
c) When restarting a saw in the workpiece,
centre the saw blade in the kerf and check
that saw teeth are not engaged into the
material. If saw blade is binding, it may walk
up or kickback from the workpiece as the saw
is restarted.
d) Support large panels to minimise the risk of
blade pinching and kickback. Large panels
tend to sag under their own weight. Supports
must be placed under the panel on both sides,
near the line of cut and near the edge of the
panel.
e) Do not use dull or damaged blades.
Unsharpened or improperly set blades
produce narrow kerf causing excessive
friction, blade binding and kickback.
f) Blade depth and bevel adjusting locking
levers must be tight and secure before making
cut. If blade adjustment shifts while cutting, it
may cause binding and kickback.
g) Use extra caution when making a "plunge
cut" into existing walls or other blind areas.
The protruding blade may cut objects that can
cause kickback.
Safety instructions guard
a) Check guard for proper closing before each
use. Do not operate the saw if guard does not
move freely and enclose the blade instantly.
8
Never clamp or tie the guard with the blade
exposed. If saw is accidentally dropped, guard
may be bent. Check to make sure that guard
moves freely and does not touch the blade or
any other part, in all angles and depths of cut.
b) Check the operation and condition of the
guard return spring. If the guard and the
spring are not operating properly, they must
be serviced before use. Guard may operate
sluggishly due to damaged parts, gummy
deposits, or a build-up of debris.
c) Assure that the guide plate of the saw will not
shift while performing the "plunge cut" when
the blade bevel setting is not at 90°. Blade
shifting sideways will cause binding and likely
kick back.
d) Always observe that the guard is covering the
blade before placing saw down on bench or
floor. An unprotected, coasting blade will cause
the saw to walk backwards, cutting whatever is
in its path. Be aware of the time it takes for the
blade to stop after switch is released.

Specific safety instructions

• Do not use misshaped or cracked blades.
• Regularly check the blades for damage. If
necessary, replace them.
• Only use blades recommended by Ferm.
• Never use a saw that has components
missing or a saw that is fitted with accessories
which were not supplied with the saw or which
are not recommended for use with the saw.
• Never exert sideways pressure on the blade
to bring it to a stop.
• Remove the plug from the plug socket before
checking whether the protective cover can
move freely and does not become stuck.
• Do not lock or clamp the protective cover.
• Do not use the saw without the protective cover.
• Before using the saw, check whether the
protective cover has been fitted.
• Always remove the plug from the plug socket
before removing the protective cover,
replacing the blade or when checking the saw
and carrying out maintenance work.
• A damaged power cord should only be replaced
by the manufacturer or a service agent.
• After use, the saw must be stored in such a
way that the blade cannot become damaged.
• Do not use abbrasive discs .
• Always wear a dust mask
• Only use saw blades recommended (e.g saw
blades intended for wood shall have EN 847-1
Ferm