Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EN
The leading beam of the laser beamer makes
sawing in straight lines much easier:
a) Along a drawn line, or
b) By aligning it to a fixed point marked on the
workpiece.
•
To switch on the laser (12), slide the laser
switch (13) to the ON position.
•
To switch off the laser (12), slide the laser
switch (13) to the OFF position.
Remove all wrenches from the machine,
before switching the machine on.
Holding and turning on the saw
Fig. 6
Holding the saw correctly makes the work lighter,
cleaner and safer.The Precision Circular Saw is
only suitable for right-handed use.
•
Slide the on-/off switch(4) forward.
•
Release the on-/off switch to switch the
machine off
Guard lock operating instructions
This tool has been fitted with a guard lock that
must be operated in order to use the tool.
•
Switch on the tool in accordance with the
instruction manual. Next release the guard
lock. Then plunge the saw blade to start the
cut. The guard lock is released by pushing in
the direction of one of the arrows in the
diagram. Either the hand holding the tool or
work piece can be used, whichever is easier.
•
After the cut has been finished and the tool
switched off, ensure the guard lock has fully
returned to its resting position. If not, unplug
the tool, remove the guard and clean
thoroughly with a soft brush.
Clamping
It is not normally necessary to clamp the material
being cut as long as it is fully supported on a work
surface and held with one hand. Clamping should
be used where;
•
The operator is inexperienced in the use of
power saws or weak handed
•
Small parts or tough material is to be cut.
Sawing
Fig. 7
12
•
A ruler can be used for clean cuts.
•
Check the technical data to see whether the
saw is suitable for use with the material to be
sawn.
•
Fit a suitable blade. Make sure the blade is
sharp and undamaged.
•
Set the sawing depth.
•
Place the material to be sawn on a flat
surface, such as a work bench, a table or the
floor. If, for example, you are working on a
concrete floor, place something, such as a
piece of cardboard, under the material to
protect the surface and the blade.
•
Insert the plug into the plug socket.
•
Hold the saw firmly and fit the metal base
plate to the material to be sawn. Make sure
the rear of the plate protrudes over the
workbench. Do not yet press the saw into the
object to be sawn.
•
Turn on the saw and wait a couple of seconds
until the saw is moving at full speed. Press the
saw slowly and carefully, but firmly, into the
material. Next, push the saw forwards along
the cutting line. Never pull the saw
backwards.
•
Only a small force is required to lead the saw
along the cutting line. Too much force will cause
damage and fatigue to the blade and the saw.
•
Make sure the base plate is always flat
against the object to be sawn. This is
particularly important at the start and finish
points of the sawing line or when small strips
must be sawn and the base plate is not
supported everywhere.
•
After sawing, lift the saw upwards and turn it
off. If a lot of sawdust has been created, allow
the saw to continue running until all the dust
has been removed.
N.B.: Always saw in the forwards direction. Never
pull the saw backwards. If you do not have much
experience using the saw, first practice sawing
wood until you become more skilled.
Cutting out shapes
Fig. 8
•
A ruler can be used for clean cuts.
•
Adjust the sawing depth, insert the plug into
the plug socket and then place the saw and
the metal base plate on the object to be sawn.
Make sure the length setting on the protective
cover is aligned with the starting point.
•
Turn on the saw and wait until the saw is
Ferm
Werbung
Inhaltsverzeichnis
