Gwarancja I Serwis; (En) Translation Of The Original Instructions - Graphite 59G184 Übersetzung Der Originalanleitung

GWARANCJA I SERWIS

Warunki gwarancji oraz opis postępowania w przypadku
reklamacji zawarte są w załączonej Karcie Gwarancyjnej.
Serwis Centralny GTX Service Sp. z o.o. Sp.k.
ul. Pograniczna 2/4 tel. +48 22 364 53 50 02-285 Warszawa e-mail
bok@gtxservice.com
Sieć Punktów Serwisowych
pogwarancyjnych dostępna na platformie internetowej gtxservice.com
Zeskanuj QR kod i wejdź na gtxservice.com
Deklaracja zgodności WE
Producent: GTX Poland Sp. z o.o. Sp.k, ulica Pograniczna 2/4 02-
285 Warszawa
Wyrób: Szlifierka kątowa
Model: 59G184
Nazwa handlowa: GRAPHITE
Numer seryjny: 00001 ÷ 99999
Opisany wyżej wyrób jest zgodny z następującymi dokumentami:
Dyrektywa Maszynowa 2006/42/WE
Dyrektywa o Kompatybilności Elektromagnetycznej 2014/30/UE
Dyrektywa RoHS 2011/65/UE zmieniona Dyrektywą 2015/863/UE
Oraz spełnia wymagania norm:
EN IEC 62841-2-3:2021+A11; EN 62841-1:2015+A11
EN IEC 55014-1:2021; EN IEC 55014-2:2021; EN IEC 61000-3-
2:2019+A1; EN 61000-3-3:2013+A1+A2
EN IEC 63000:2018
Deklaracja ta odnosi się wyłącznie do maszyny w stanie, w jakim została
wprowadzona do obrotu i nie obejmuje części składowych
dodanych przez użytkownika końcowego lub przeprowadzonych przez
niego późniejszych działań.
Nazwisko i adres osoby mającej miejsce zamieszkania lub siedzibę w
UE upoważnionej do przygotowania dokumentacji technicznej:
Podpisano w imieniu:
GTX Poland Sp. Z o.o. Sp.k. Ulica Pograniczna 2/4
02-285 Warszawa
Paweł Kowalski
Pełnomocnik ds. dokumentacji technicznej GTX Poland
Warszawa, 2024-01-16
Varsovie, 2024-01-16
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
ANGLE GRINDER 58G184
CAUTION Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all of
the instructions below may result in electric shock, fire and/or serious
injury.
Keep all warnings and instructions for future reference.
• This power tool is designed to be used as a grinder, polisher or
cutter. Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all of
the instructions below may result in electric shock, fire and/or
serious injury.
• Do not use this power tool for sanding, wire brushing or cutting
holes. Operations for which the power tool is not designed may
create hazards and cause personal injury.
• Do not modify this power tool in any way that is not expressly
provided for and specified by the tool manufacturer. Such
modification may result in loss of control and serious personal
injury.
• Do not use accessories that are not specifically designed and
specified by the tool manufacturer. The mere fact that an accessory
fits the power tool does not guarantee safe operation.
do napraw gwarancyjnych
(EN)
• The rated speed of the accessory must be at least equal to the
maximum speed specified on the power tool. Accessories operating
at speeds higher than the rated speed may be damaged and break
into pieces.
• The outer diameter and thickness of the accessory must be within
the rated parameters of the power tool. Accessories with
inappropriate dimensions cannot be properly secured or controlled.
i
• The mounting dimensions of the accessory must match the
mounting dimensions of the power tool. Accessories that do not fit
the mounting dimensions of the power tool will become unbalanced,
vibrate excessively and may cause loss of control.
• Do not use damaged accessories. Before each use, check
accessories such as grinding wheels for chips and cracks, grinding
wheel pads for cracks, tears or excessive wear, and wire brushes
for loose or broken wires. If the power tool or accessory has been
dropped, check it for damage or install undamaged accessories.
After checking and installing the accessory, ensure that the
operator and bystanders are clear of the rotating accessory plane
and run the power tool at maximum speed without load for one
minute. Damaged accessories will usually fail during this test.
• Wear personal protective equipment. Depending on the application,
use a face shield, safety glasses or safety goggles. If necessary,
wear a dust mask, ear protection, gloves and a workshop apron to
protect against small abrasive particles or fragments of the
workpieces. Eye protection must be able to stop fragments
generated during various applications. The dust mask or respirator
must be capable of filtering the particles generated during the
application. Prolonged exposure to high noise levels can cause
hearing loss.
• Bystanders should keep a safe distance from the work area.
Anyone entering the work area must wear personal protective
equipment. Fragments of the workpiece or damaged equipment
may fly off and cause injury outside the immediate work area.
• When performing operations where the cutting tool may come into
contact with hidden wiring or its own cable, hold the power tool only
by its insulated gripping surfaces. Contact between the cutting tool
and a live wire may cause exposed metal parts of the power tool to
become live, which may result in electric shock to the operator.
• Keep the cable away from the rotating part. If you lose control, the
cable may be cut or snagged, and your hand or arm may be pulled
into the rotating part.
• Never put down the power tool until the accessory has come to a
complete stop. The rotating accessory may catch on the surface
and pull the power tool out of your hands.
• Do not use the power tool while carrying it. Accidental contact with
the rotating accessory may cause it to snag on clothing and pull the
accessory towards the body.
• Clean the ventilation openings of the power tool regularly. The
motor fan draws dust into the housing, and excessive accumulation
of powdered metal can cause an electrical hazard.
• Do not use power tools near flammable materials. Sparks may
ignite these materials.
• Do not use accessories that require liquid coolants. The use of
water or other liquid coolants may result in electric shock or electric
shock.
• Only use the types of discs specified for the power tool and guards
designed for the selected discs. Discs for which the power tool is
not designed may not be adequately protected and are dangerous.
• The grinding surface of wheels with a centre recess must be
mounted below the plane of the guard edge. An incorrectly mounted
wheel that protrudes beyond the plane of the guard edge cannot be
adequately protected.
• The guard must be securely attached to the power tool and
positioned for maximum safety, so that as little of the disc surface
as possible is exposed towards the operator. The guard protects
the operator from disc fragments, accidental contact with the disc
and sparks that could ignite clothing.
• Discs may only be used for specific applications. For example: do
not grind with the side of a cutting disc. Cutting abrasive discs are
designed for peripheral grinding, and lateral forces applied to these
discs may cause them to fracture.
• Always use undamaged flanges that are the correct size and shape
for the selected disc. Proper disc flanges support the disc, thereby
reducing the risk of breakage. Flanges for cutting discs may differ
from flanges for grinding discs.
8