GRAPHITE 58G077 Übersetzung Der Originalanleitung Seite 10

Number of teeth per Length
inch
24
14 80 mm
9
• Use only appropriate and sharp saw blades.
• Do not use blades with a damaged shank.
• Use the correct types of saw blades.
OPERATION AND MAINTENANCE
Unplug the power cord from the mains socket before carrying
out any installation, adjustment, repair or operation.
• It is recommended to clean the device immediately after each
use.
• Do not use water or other liquids for cleaning.
• The unit should be cleaned with a dry piece of cloth or blown
with low-pressure compressed air.
• Do not use any cleaning agents or solvents, as these may
damage the plastic parts.
• Clean the ventilation slots in the motor housing regularly to
prevent the unit from overheating.
• It is recommended that the guide roller be lubricated
periodically. A drop of oil applied to this area will prolong its life.
• If the power cable is damaged, it must be replaced with a cable
of the same characteristics. This operation should be entrusted
to a qualified specialist or have the appliance serviced.
• If excessive sparking occurs on the commutator, have the
condition of the motor's carbon brushes checked by a qualified
person.
• Always store the device in a dry place out of the reach of
children.
REPLACEMENT OF CARBON BRUSHES
Worn (shorter than 5 mm), burnt or cracked motor carbon
brushes must be replaced immediately. Always replace both
carbon brushes at the same time.
Only a qualified person should replace the carbon brushes
using original parts.
Any defects should be rectified by the manufacturer's authorised
service department
TECHNICAL SPECIFICATIONS
RATING DATA
Parameter
Supply voltage
Supply frequency
Rated power
Number of blade cycles (no
load)
Max. thickness of material to be
cut - wood
Max. thickness of material to be
cut - metal
Blade stroke
Degree of protection
Protection class
Mass
Year of production
NOISE AND VIBRATION DATA
Sound pressure level
Sound power level
Vibration acceleration values
(slab cutting)
Vibration acceleration values
(metal sheet cutting)
58G077 indicates both the type and the designation of the
Scope of application
Soft steel, non-ferrous metals.
Non-ferrous metals, plastics.
Wood, wooden plywood.
Value
230 V AC
50 Hz
800 W
-1
0-3100 min
80 mm
10 mm
18 mm
IPX0
II
2 kg
2025
Lp = 87,6 dB(A) K= 3
A
dB(A)
Lw = 95.6 dB(A) K= 3
A
dB(A)
2
a = 4.535 m/s K= 1.5
h
2
m/s
2
a = 4.008 m/s K= 1.5
h
2
m/s
machine
Information on noise and vibration
The noise emission level of the equipment is described by: the
emitted sound pressure level Lp
where K denotes measurement uncertainty). The vibration emitted
(
by the equipment is described by the vibration acceleration value
a where K is the measurement uncertainty).
(h) (
The sound pressure emission level Lp
vibration acceleration value a
measured in accordance with EN 62841-1:2015. The vibration level
a given can be used for comparison of equipment and for
h
preliminary assessment of vibration exposure.
The vibration level quoted is only representative of the basic use of
the unit. If the unit is used for other applications or with other work
tools, the vibration level may change. A higher vibration level will
be influenced by insufficient or too infrequent maintenance of the
unit. The reasons given above may result in increased vibration
exposure during the entire working period.
In order to accurately estimate vibration exposure, it is
necessary to take into account periods when the unit is
switched off or when it is switched on but not used for work.
Once all factors have been accurately estimated, the total
vibration exposure may turn out to be much lower.
In order to protect the user from the effects of vibration, additional
safety measures should be implemented, such as cyclical
maintenance of the machine and working tools, securing an
adequate hand temperature and proper work organisation.
ENVIRONMENTAL PROTECTION
Electrically-powered products should not be disposed of with
household waste, but should be taken to appropriate facilities for
disposal. Contact your product dealer or local authority for information
on disposal. Waste electrical and electronic equipment contains
substances that are not environmentally friendly. Unrecycled
equipment poses a potential risk to the environment and human
health.
"GTX Poland Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa with
its registered office in Warsaw, ul. Pograniczna 2/4 (hereinafter: "GTX Poland ")
informs that all copyrights to the content of this manual (hereinafter: "Manual"),
including among others. All copyrights to the contents of this Manual (hereinafter
referred to as "Manual"), including but not limited to its text, photographs, diagrams,
drawings, as well as its composition, belong exclusively to GTX Poland and are
subject to legal protection under the Act of February 4, 1994 on Copyright and
Related Rights (i.e. Journal of Laws 2006 No. 90 Item 631 as amended). Copying,
processing, publishing, modifying for commercial purposes the entire Manual as well
as its individual elements without the written consent of GTX Poland is strictly
prohibited and may result in civil and criminal liability.
EC Declaration of Conformity
Manufacturer: GTX Poland Sp. z o.o. Sp. k.,
2/4 Pograniczna Street
02-285 Warsaw
Product: Jigsaw
Model: 58G077
Trade name: GRAPHITE
Serial number: 00001 ÷ 99999
This declaration of conformity is issued under the sole responsibility
of the manufacturer.
The product described above complies with the following documents:
Machinery Directive 2006/42/EC
Electromagnetic Compatibility Directive 2014/30/EU
RoHS Directive 2011/65/EU
2015/863/EU
And meets the requirements of the standards:
EN 62841-1:2015+A11:2022;
11:2016+A1:2020+A11:2024;
EN IEC 55014-1:2021; EN IEC 55014-2:2021; EN IEC 61000-3-
2:2019+A1:2021; EN 61000-3-3:2013+A1:2019+A2:2021;
EN IEC 63000:2018
This declaration relates only to the machinery as placed on the market
and does not include components
added by the end user or carried out by him/her subsequently.
Name and address of the EU resident person authorised to prepare
the technical dossier:
Signed on behalf of:
GTX Poland Sp. z o.o. Sp.k.
2/4 Pograniczna Street
10
and the sound power level Lw
A
, sound power level Lw
A
given in these instructions have been
h
as amended by
EN
(A)
and
A
Directive
62841-2-