Storing And Erasing Presets; Manual Storing; Automatic Storing (Autostore); Erasing Presets - T+A R 1260 R Betriebsanleitung

The receiver can store a total of 60 device settings
(presets). A preset contains all the current settings, i.e.
WIDE/NARROW, MONO/STEREO etc., in addition to the
frequency.
When you call up a preset the receiver is returned to the
exact state it was in when you stored the setting.
When you are using the storage and erasure functions it
is not possible to change the reception mode (WIDE /
ATTENUATOR / MONO), change the mode of operation
(preset select / tuning) or call up the display functions.

Manual storing

First tune in the station to be stored as accurately as you
can, then press the   button. The display first
 
switches to normal brightness, regardless of the pre-
viously set brightness level. On the right of the screen
you will see the transmitter frequency, and on the left a
' ' followed by a flashing number.
P P P P
This figure is the preset number under which the station
setting will be stored. The number can be changed to any
other using the   and 
 
a remote control system (see section 'Remote Control'),
you can use the numeric pad on the remote control unit
to change this number.
Once you have set the preset number you want, simply
press the   button and hold it pressed in for about
 
a second until the display shows the message '
That station is now stored, and can be called up at any
time by selecting its preset number.
You may want to interrupt the memory function without
storing a preset; just press the 
the receiver immediately returns to the normal display.

Erasing presets

First select the preset to be erased using the 
 buttons, or, if available, using the numeric pad on
  
the Remote Control handset. Press the 
The preset number on the screen will now flash, and you
can change it as in the manual storing process. Tap the
 button repeatedly until the message '

 
appears on the screen.
Press the   button and hold it pressed in until the
 
preset number stops flashing. The preset is now erased.
If you wish to interrupt the erasure process, simply tap
the   button briefly, without holding it pressed in.
 

Storing and erasing presets

 buttons. If you have
 
STORE STORE STORE STORE
 button briefly, and
 
 and
 
 button.
 
CLEAR CLEAR
CLEAR CLEAR
Automatic storing
When this function is switched on, the receiver auto-
matically searches the entire FM band for stations which
will be received at high quality in the reception mode
"STEREO / NARROW", and automatically stores the sta-
tions it finds.
Using the AUTOSTORE function: first press the 
button. You can now select a preset number as the
starting point (as when storing stations manually) using
the   and   buttons (you can also enter a
   
number directly from the remote control unit). The
stations found will then be stored in the memory locations
following this starting number. If all the station memories
are to be used, select the number 01.
Once you have set the initial preset, tap the 
button repeatedly until the message '
the screen.
To initiate the automatic storing process press the
 button and hold it pressed in for about a second

 
until the frequency display on the screen starts to incre-
ment (run upwards). You can now follow the process of
seeking and storing stations by watching the screen.
The AUTOSTORE function ends automatically once the
whole FM band has been searched, or when all the
memories have been used.
Note:
As the tuner is unable to assess the quality of reception
'.
of the individual stations, you can revise manually the
presets which are stored automatically.
To do this, call up each preset in turn and try to improve
the reception quality by changing the reception mode
(WIDE / ATTENUATOR / MONO); then manually store
the preset again (see 'Manual Storing').
If you find presets for stations which are not worth recei-
ving, or if you find duplicate stations on different fre-
quencies, simply erase those presets (see 'Erasing
Presets').
'
33
(AUTOSTORE)

 
  
' appears on
AUTO AUTO AUTO AUTO