Multiplex filius Bauanleitung Seite 12

.':\
Dritra rrote in part 3+ to accomodate dowet35.
- "'n""1*","
the position of screw 37 in the middle or t(ilnopy nottot.
Glue part 34 onto part 33, while these a[e still laying on the fuselage. While adding some glue, screw in screw 37 into the nose block jusl
During this glueing process, it is imperative to slip a piece ol plastic enough so that the canopy bottom may still be lifted easily.
sheet or household wrapping materialbetween part3Sand the fuseiage- Smear the outline of the canopy bottom with glue and put the canopy
sides so aa to make sure than the canopy frame will not stick to the
into place. Hold the canopy into place with cloth-pins. Once the glue
fuselage.
is entirely dry, take offthe cloth-pins and clean the canopy.lf necessary,
Trim canopy 36 so that it overlaps the canopy frame.
trim the canopy somewhat more so that it matchesthe tuselage exactly
Match the canopy lrame to Ü," tus"r"g". No* siape fte top part of
This completes the building of the fuselage'
the nose block so that it matches the canopy bottom according to the
Empennage (fn assembly and stabilizgr)
contour shown on the drawings. During thesanding, check.from time
Glue the two stabilizer tips 27 lo part 26 and makä sure your trailing
to time that the conect outline is given to the fuselage, using the _caropy edge is perfeclly straight. lf necessary, u9e your sanding block so as t;
as a refeience. In the process ot all this streamlining, part 33 will finally
obüin a perfecüy straight line at this point. Gtue into place leading
acquite a beveled edge
edge 28, Firsl glue the right part ol the leading edge and let the glue
Shave about 0.5 mm off the outline of the canopy frame so as lo allow
joi;t dry. Righain the miJdle, at the place which is located under the
for the thickness of the canopv itself. Position tle.:lnopJ 99t1111"
iin, ""nä ttrJ rigtt-h"nd teading edge in tine with rhe tett-hand portion
the fuselage and drill a hole in part 1 2, through th€ hole located in Jormer
ot the stabilizer; all you have to d; next is glue in place the teft-hand
34. cut dowel 35 to length and round off its end Glue dowel 35 into
Lading eoge, let it äry, and then sand according to the plan view ol
Pat112
the stabilizer.
Adapt the stabilizer to the fuselage, which will only be possible if you
have given the center section ol the leading edge the desired shape
as per plan. Sand the stabilizer according to the section shown.
Match the elevator to the stabilizer. Give the elevator tips the shape
which matches the contour of th€ stabilizer
In oder to be able to install the lhree elevator hinges, you will have
to cut three slots at the äppropriate locations, in the stabilizer as well
as in theelevator. Determine wh€rethe slotsshould be madebyrelerring
to the Dlan.
To make the slotting for the hinges easie( we would advise you to buy
a Carl Goldberg'Hinge Slotting kit' (also distributed in Europe by Multi-
plex under their Order nr 3156). Slotting the parts to r€ceive the hinges
will be an easy task if you use this special slotting tool.
Do not glue the hinges into place at this particular point; once the parts
have been prop€rly slotted, you only need push the hinges into the
slots 'dry' to see if they work, then you can disconnect the elevator
trom the stabilizer again.
?2
(
, ,
,
.1:.-.',
'--'')-'
,
--'
/ I --1.
zz%
4"%
22