Werbung
Verfügbare Sprachen
Verfügbare Sprachen
WARNING
This power tool generates an electromagnetic field
during operation. This field can impair active or passive
medical implants under certain circumstances. In order
to prevent the risk of serious or deadly injuries, we rec-
ommend that persons with medical implants consult
with their physician and the manufacturer of the medical
implant prior to operating the power tool.
WARNING
In case of extended working periods, the operating per-
sonnel may suffer circulatory disturbances in their
hands (vibration white finger) due to vibrations.
Raynaud's syndrome is a vascular disease that causes
the small blood vessels on the fingers and toes to
cramp in spasms. The affected areas are no longer
supplied with sufficient blood and therefore appear ex-
tremely pale. The frequent use of vibrating products can
cause nerve damage in people whose circulation is im-
paired (e.g. smokers, diabetics).
If you notice unusual adverse effects, stop working im-
mediately and seek medical advice.
ATTENTION
The product is part of the 20V IXES series and may on-
ly be operated with batteries of this series. Batteries
may only be charged with battery chargers of this se-
ries. Observe the manufacturer's instructions.
WARNING
Follow the safety and charging instructions
and correct usage given in the instruction
manual of your 20V IXES Series battery and
charger.
A
detailed
charging process and further information are
provided in this separate manual.
6
Technical data
Cordless angle grinder
Motor voltage
Speeds n
0
Dimension of cutting wheel
Thread dimension
Weight (without battery)
Subject to technical changes!
Noise and vibration
WARNING
Noise can have serious effects on your health. If the
machine noise exceeds 85 dB, please wear suitable
hearing protection for you and persons in the vicinity.
The noise and vibration values have been determined in
accordance with EN 62841-1.
22 | GB
description
of
the
BC-AG125-X
20 V
rpm
3000 - 10000
Ø 125 mm
M14
1.60 kg
www.scheppach.com
Noise data
Sound pressure L
pA
Measurement uncertainty K
Sound pressure L
wA
Measurement uncertainty K
Vibration parameters
Surface grinding
Main handle Vibration a
h
Measurement uncertainty K
Additional handle Vibration a
Measurement uncertainty K
The total vibration emission values specified and the de-
vice emissions values specified have been measured in
accordance with a standardised test procedure and can
be used for comparison of one electric tool with another.
The total noise emission values specified and the total vi-
bration emission values specified can also be used for an
initial estimation of the load.
WARNING
The noise emission values and vibration emis-
sion value can vary from the specified values
during the actual use of the power tool, de-
pending on the type and the manner in which
the electric tool is used, and in particular the
type of workpiece being processed.
Try to keep the stress as low as possible. For example:
Limit working time. In doing so, all parts of the operating
cycle must be taken into account (such as times in
which the power tool is switched off or times in which it
is switched on, but is not running under a load).
7
Before commissioning
WARNING
Danger of injury!
Remove the battery from the power tool before carrying
out any work on the power tool (e.g. maintenance, tool
change, etc.) and when transporting and storing it.
There is a risk of injury if the on/off switch is operated
unintentionally.
7.1
Assemble/disassemble additional
handle (3) (Fig. 1+8)
ATTENTION
Only use the product with the additional handle fitted.
Assembling the additional handle
Note:
The additional handle can be screwed in on the left, right
or top of the product head.
1. Tighten the additional handle (3) clockwise.
Removing the additional handle
1. Remove the additional handle (3) from the product by
unscrewing it anticlockwise.
83 dB
3 dB
94 dB
3 dB
2.698 m/s
1.5 m/s
3.284 m/s
h
1.5 m/s
2
2
2
2
Werbung
