Scheppach 5904809904 Originalbetriebsanleitung Seite 45

Wear Parts
Even when used in the intended way, some compo-
nents are subject to normal wear. They have to be
replaced depending on the kind of duration of usage.
These parts include, among others, the cutting tool
and the retaining disk.
m Warning! Use only original manufacturer's re-
placement parts, accessories and attachments. Fail-
ure to do so can cause poor performance, possible
injury and may void your warranty
Important hint in case of sending the equipment
to a service station:
Due to security reasons please see to it that the
equipment is sent back free of oil and gas!
Ordering replacement parts
Please quote the following data when ordering re-
placement parts:
• Type of machine
• Article number of the machine
Replacement parts / accesories:
For the cutting equipment listed here, you can always
use the safety guards provided with the unit.
Grass trimmer/brush cutter:
Spool with Ø 450
Spool TRICORD Ø450
Spare spool TRICORD
Blade with 3 teeth Ø 255 x 1.4
Transport guard for blade 3 teeth
Blade with 4 teeth Ø 255 x 1.5
Transport guard for blade 4 teeth
Blade with 8 teeth Ø 255 x 1.5
Transport guard for blade 8 teeth
Safety shield for grass trimmer
Pole pruner:
Saw chain Oregon 91PJ040X
Guide rail Oregon 100SDEA318
Transport guard for chain
Extension for pole pruner
Hedge trimmer:
Blade for hedge trimmer 400 mm
Transport guard for blade
11. Storage
Cleaning
• Keep handles free of oil, so you always have a secure
hold.
• Clean the equipment as required with a damp cloth and,
if necessary, mild washing up liquid.
m Important!
• Always pull out the spark boot plug each time before car-
• Never immerse the equipment in water or other liquids in
• Store the petrol multi garden tool in a safe and dry place
Storage
Important: Never put the equipment into storage for longer
than 30 days without carrying out the following steps.
Storing the equipment
If you intend to store the equipment for longer than 30 days,
the equipment must be prepared accordingly. Otherwise
the fuel still remaining in the carburetor will evaporate and
leave a rubbery sediment. This can cause problems when
starting up the equipment and may require expensive re-
pairs.
1 Slowly remove the fuel tank cap to release any pres-
2 To remove the fuel from the carburetor, start the engine
3 Leave the engine to cool (approx. 5 minutes).
4 Remove the spark plug (see section 10 Change and
5 Add one teaspoon of 2-stroke engine oil into the com-
7910700706
7910702702
7910702704
7910700702
3904801065 Note: Store the equipment in a dry place and far away from
7910700705 possible ignition sources such as an oven, a gas-fi red hot
3904801066 water boiler, a gas-fi red dryer, etc.
7910700711
3904801066 Putting the equipment back into operation
3904803034 1 Remove the spark plug (see section 10 Change and
7910700704 2 Quickly tug on the starter cord to remove excess oil
3904801037
3904801039 3 Clean the spark plug and check that the electrode gap
7910700710
7910700703 4 Prepare the equipment for operation.
3904801043 5 Fill the tank with the relevant mixture of fuel and oil.
Transport
To transport the machine, empty the petrol tank as de-
scribed in section 8 draining fuel. Clean coarse dirt off the
equipment with a brush or hand brush.
Always attach the transport guard to all cutting tools. Fig. 1
(14a, 15a, 17a)
In order to prevent damage and injury, secure the tool
against tipping over and sliding when transporting it in ve-
hicles.
www.scheppach.com
rying out any cleaning.
order to clean it.
out of the reach of children.
sure that may have formed in the tank. Carefully empty
the tank.
and let it run until the equipment stops.
clean the spark plug).
bustion chamber. Slowly pull the starter cord several
times to apply a layer of oil to all internal components.
Fit the spark plug again.
clean the spark plug).
from the combustion chamber.
is correct, or insert a new spark plug with the correct
electrode gap.
See the section „Fuel and oil".
GB | 45