Herunterladen Diese Seite drucken

Husqvarna TS 300 E Bedienungsanweisung Seite 5

Vorschau ausblenden Andere Handbücher für TS 300 E:

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

operates without problems. Incorrect voltage
causes the power consumption and the
temperature of the motor to increase until
the safety circuit releases. The dimension
of the power cord must agree with national
and local regulations. The dimension of the
mains socket must agree with the amperage
for the electrical socket and extension cable
of the product.
If the power mains has higher system
resistance, short voltage drop can occur
when the product is started.
Make sure that the power, fuse and mains voltage
are the same as the voltage shown on the rating
plate of the product.
Always stop the product before you disconnect the
power plug.
Do not use the product if the power cord or power
plug is damaged. Hand it in to an approved service
center for repair. A damaged power cord can cause
serious injury or death.
Use the power cord correctly. Do not use the power
cord to move, pull or disconnect the product. Pull the
power plug to disconnect the power cord. Do not pull
the power cord.
Do not operate the product in water depths where
the equipment of the product gets wet. The
equipment can become damaged and the product
can become live and cause injury.
Always connect the product with a ground fault
circuit that releases at a ground fault of 30 mA.
Do not get more moisture into the product than
the water supplied by the water system. Keep the
product away from rain. Water that goes into the
product increases the risk of electrical shock.
Only connect the product to correctly grounded
outlet.
Always disconnect the power cord before you
connect or disconnect the connection for the motor
cable and the electrical enclosure.
Grounded product instructions
WARNING:
result in electrical shock. Speak to an
approved electrician if you are not sure if
your mains outlet is correctly grounded.
Do not do modifications to the power plug
from its factory specification. If the power
plug or power cord is damaged or must be
replaced, speak to your Husqvarna service
agent. Obey local regulations and laws.
If you do not fully understand the
instructions about the grounded product,
speak to an approved electrician.
2282 - 002 - 07.02.2024
Incorrect connection can
Use only grounded outdoor extension cables with
grounding plugs and grounding outlet that accepts the
product power plug.
The product has a grounded power plug. Always
connect the product to a grounded mains outlet. This
decreases the risk of electrical shock if there is a
malfunction.
Do not use electrical adapters with the product.
Extension cables
Use only approved extension cables with approved
length that fullfils the requirements. Refer to
Extension cables on page 20 .
The rated value on the extension cable must be the
same or higher than given on the rating plate of the
product.
Use grounded extension cables.
When you operate the product outdoors, use
an extension cable that is applicable for outdoor
operation. This decreases the risk of electrical
shock.
Keep the connection to the extension cable dry and
off the ground.
Keep the extension cable away from heat, oil, sharp
edges or moving parts. A damaged cable increases
the risk of electrical shock.
Make sure that the extension cable is in good
condition and not damaged.
Do not use the extension cable while it is wound up.
This can cause the extension cable to become too
hot.
Safety instructions for assembly
WARNING:
instructions that follow before you assemble
the product.
Always use protective gloves when you assemble
the product.
Make sure that the product is on a surface that is
flat and stable. Surface that is not flat and stable
increases the risk for the saw to tilt or move.
Make sure that you push the OFF button and that
the product is OFF.
Make sure that the power plug is disconnected.
Make sure that the cutting blade does not move.
Always use accessories that are approved by the
manufacturer.
Make sure that the cutting blade, blade guard, blade
flange and blade shaft are not damaged.
Safety instructions for operation
WARNING:
and all instructions. Failure to follow the
Read the warning
Read all safety warnings
5

Werbung

loading

Diese Anleitung auch für:

Ts 350 eTs 400 f