Kärcher KM 130/300 R LPG Kurz- Betriebsanleitung Seite 9

by slowly letting out the gas in open
spaces by conforming to all safety reg-
ulations and are to be indicated as
leaky. Also inform the issuing company
or its representative (the filling-station
attendant) in writing about the damage
to the cylinder while delivering or re-
ceiving the cylinders.
Before connecting the gas cylinder,
–
check that its connection neck is in a
proper state.
After connecting the cylinder, regularly
–
check that it is not leaky by using a
foaming agent.
Open the valves slowly. Do not use
–
hammers to open and close the cylin-
ders.
Fight liquid-gas fires only from a safe
–
distance and with protection.
- use only dry powder carbon dioxide
extinguishers or carbon dioxide gas ex-
tinguishers.
- use abundant water to cool the gas
tank.
The entire LPG unit must be continu-
–
ously checked to ensure that there are
no leaks and the unit is functioning
properly. Using the vehicle with a leaky
gas unit is strictly prohibited.
First close the cylinder valve before
–
loosening the pipe or tube connection.
Unscrew and loosen the connection nut
of the gas cylinder slowly because oth-
erwise the gas under pressure in the
tube will flow out instantly.
If the gas is refilled from a larger tank,
–
then ask the sales agent of the LPG
about the important regulations to be
followed.
Danger
Risk of injury!
LPG in a liquid state can cause frost
–
bites on bare skin.
After disconnecting the cylinder, tighten
–
the closing nut firmly on the connecting
threading of the cylinder.
Use soap water or some such foaming
–
agent to check whether the cylinder is
leaking. The use of open flames to illu-
minate the LPG unit is strictly prohibit-
ed.
Follow the manufacturer's installation
–
specifications while changing individual
parts of the LPG unit. Close all cylinder
and locking valves while doing so.
Regularly check the status of the elec-
–
trical unit of the LPG vehicles . Sparks
can cause explosions if the gas-carry-
ing parts of the unit are leaky.
If a LPG-driven vehicle has been idling
–
for a long time, then first ventilate the
setting room before commissioning the
vehicle or its electrical unit.
Immediately inform the trade associa-
–
tion and the concerned trade superviso-
ry authority about accidents with gas
cylinders or LPG units. Store the dam-
aged parts carefully until all investiga-
tions have been completed.
In the installation and storage rooms as
well as the workshops
Propellants or LPG cylinders must al-
–
ways be stored according to the regula-
tions of TRF 1996 (Technical
Regulations for Liquid Gases, refer DA
to BGV D34, Appendix 4).
Always store the gas cylinders in a ver-
–
tical position. Use of open flames and
smoking at the installation site of the
cylinders and during repairs is strictly
prohibited. Protect the stored cylinders
against unauthorised access. Close all
empty cylinders properly.
Close the cylinder and main locking
–
valves immediately when you switch off
the vehicle.
Follow the regulations for garages and
–
the construction guidelines of the re-
spective State about the location and
structure of the parking areas for LPG-
driven vehicles.
Gas cylinders are to be stored in sepa-
–
rate rooms away from the parking areas
(refer DA to BGV D34, Appendix 2).
The electrical hand-held lamps used in
–
the rooms are to be equipped with
closed, sealed case and a strong pro-
tection cover.
Close all cylinder and main valves be-
–
fore working in repair workshops and
protect the gas cylinders against effect
of external heat.
A responsible person must check that
–
all valves, especially the cylinder
valves, are closed during operational
breaks and before closing the factory.
Do not carry out any jobs involving fire -
such as cutting and welding jobs - in the
vicinity of the gas cylinders. Do not
store gas cylinders, not even empty
ones, in the workshops.
The parking and storage rooms and the
–
repair workshops must be ventilated
properly. Please note that liquefied
gases are heavier than atmospheric air.
They get collected on the floor, in re-
cesses and other holes in the floors and
form a gas-air mixture that can lead to
explosions.
Symbols in the operating instruc-
tions
Danger
Immediate danger that can cause severe
injury or even death.
Warning
Possible hazardous situation that could
lead to severe injury or even death.
Caution
Possible hazardous situation that could
lead to mild injury to persons or damage to
property.
2
-
EN
Symbols on the machine
Risk of burns on account
of hot surfaces! Allow the
exhaust to cool down suf-
ficiently before starting
work on the machine.
Always use appropriate
gloves while working on
the device.
Risk of getting squeezed
on account of getting
jammed between vehicle
parts.
Risk of injury on account
of moving parts. Do not
reach in.
Risk of fire. Do not vacu-
um up any burning or
glowing objects.
Chain pick-up / crane
point
Lashing point
Tyre pressure (max.)
Intake points for the jack
Brush roller adjustment
Maximum decline of
ground when driving with
the waste container
raised.
The gradient in the direc-
tion of travel should not
exceed 18%.
Observe the installation
position of the gas cylin-
der. The connection / ring
opening must point
downwards.
9