Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ATTENTION: The cutter blade rotates even when
the engine brake lever is released as soon as you
pull the cable starter. Make sure that there are no
body parts in the danger zone of the cutting blade.
• When the engine is running, press the drive lever
(2) to the handle (1) in order to engage the drive on
the mower.
• Before you start mowing, you should run through
this process several times in order to ensure that
the machine is working properly.
m WARNING
Whenever you need to perform any kind of ad-
justment and/or repair work on your lawnmower,
wait until the blade has come to a complete stop.
Always switch off the engine and take out the
spark plug before carrying out any adjustments,
maintenance or repairs.
Using the drive:
• Engine brake: Use the engine brake lever (3) to stop
the engine. When you release the engine brake le-
ver, the engine and cutter stop automatically.
• To mow, pull the drive lever (2) towards the han-
dle (1). Before actually mowing, check the engine
brake lever (3) several times. Ensure that the pull
cable can be smoothly operated.
• Drive lever (2):
If you press this, the clutch for the drive will be
closed and the lawnmower will start to move with
the engine running. Release the drive lever in good
time to stop the moving lawnmower. Practice start-
ing and stopping before you use the mower for the
first time until you are familiar with controlling the
mower.
Warning: The cutter blade rotates when the engine
is started.
Important: Before starting the engine, move the en-
gine brake several times to check that the stop cable
is also working well.
Note: The engine is designed for the cutting speed
for grass, and grass ejection into the catch basket
and for a long engine service life
• Check the oil level.
• Open the fuel fuel cap and fill the fuel tank (6) up
to the lower point of the tank inlet with about 0,85
litres of petrol. Use a funnel and measuring con-
tainer for filling. Do not overfill the tank. Only use
fresh, clean, unleaded fuel.
Never mix oil with petrol. Purchase fuel in quanti-
ties that can be used within 30 days to ensure that
the fuel is fresh.
Note: Use standard unleaded petrol with max. 10%
bioethanol component.
36 | GB
m WARNING
Always only use a safety petrol canister. Do not
smoke when filling petrol. Remove any oil or petrol
residues. Switch the engine off before filling petrol
and let the engine cool for several minutes.
Start the engine (Fig. 14a)
• Check the motor oil level. See "oil level check" sec-
tion.
• Inspect the battery compartment at the top of the
electric starter unit (18) for foreign objects and
clean with a brush or cloth if necessary. Install the
battery in the battery compartment on the electric
starter unit (18) (Fig. 27). Make sure that the battery
is securely fastened. The battery is the key to the
device.
• Make sure that the controls for the device drive, if
any, are out of operation.
• Press the engine brake lever (3) against the handle
(1). Operate the electric starter (17a). The engine
will start.
Start the engine (Fig. 14)
• Make sure that the device is connected properly to
the spark plug.
• Stand behind the mower. One hand pushes the en-
gine brake lever (3) to the handle (1), the other hand
should be on the cable starter (17).
• Start the engine with the pull cable starter (17). To
do this pull the handle approx. 10 – 15 cm (until you
feel a resistance) and then start the engine with a
sharp pull. If the engine does not start, pull on the
handle again.
• Due to protective coating on the engine, a small
amount of smoke may be present during the initial
use of the device and should be considered nor-
mal. This is a normal process.
m Attention!
• Never allow the pull cable starter to snap back.
• Attention: In case of cool weather, it may be nec-
essary to repeat the starting process numerous
times.
Switch the engine off:
• To turn off the engine, release the drive lever (2),
then the engine brake lever (3) and wait for the
blades to stop.
• Pull the spark plug connector off the spark plug (10)
to prevent unintentional start of the engine.
• Before you start the engine again, check the cable
for the engine brake. Check that the cable is cor-
rectly fitted. If the cable is kinked or damaged, it
should be replaced.
• Remove the battery. The battery is the key to the
device.
www.scheppach.com
Werbung
