Werbung
Verfügbare Sprachen
Verfügbare Sprachen
HYUNDAI
Starting the engine
When the engine has started, the throttle must be gently
actuated once so that the engine reaches the correct idling
speed and the saw chain does not start at idling speed.
•
Remove sheath from the cutting mechanism.
•
Move operating switch (8) to On [I] position.
•
Activate the chain brake.
Starting with a cold engine
1. Pull out choke (12) all the way .
2. Place the machine on the ground and pull the starter cable in a
controlled and continuous movement.
Pull out the starter cable maximum 50 cm and slowly guide
back by hand.
3. If the engine wants to start, press in choke (12) again.
4. Pull the starter cable in a controlled and continuous movement
until the engine starts.
5. Press the throttle lock (10) and gently actuate the throttle (9).
6. Release the chain brake.
Starting with a warm engine (fig. G)
1. Place the machine on the ground and pull the starter cable in a
controlled and continuous movement until the engine starts (Fig.
9).
2. Press the throttle lock (10) and actuate the throttle (9).
If the engine does not start after pulling the starter cable
3–4 times, repeat the entire starting process as described
under "Starting with a cold engine".
3. Release chain brake.
4. Leave the engine running for 1 to 2 minutes to warm up.
At lower temperatures the engine may take longer to warm
up and reach maximum speed.
The machine has warmed up properly when the engine
accelerates without faltering.
Stop the engine
•
Release the throttle (9). Leave the engine to cool down at idling
speed.
•
Move the operating station (8) to the Stop [0] position.
To prevent starting the engine unintentionally, always
remove the spark-plug terminal from the spark plug if the
machine is left unattended.
USE
Before using the machine
•
Before starting work, check the safety of the machine (see
section "Before starting the machine").
•
Familiarise yourself thoroughly with the sawing technique of
chain saws. Information can be found in the specialist literature.
20
Correct posture
Never work on unstable ground!
Never work above shoulder height!
Never work while standing on a ladder!
Do not bend too far forwards when working!
Use the machine only when the weather conditions and
terrain are favourable!
•
Stand with both legs firmly on the ground.
•
Beware of obstructions in the working area.
•
When working, always hold the machine with both hands!
Hold the machine:
-
with your left hand on the front handle,
-
with your right hand on the rear handle.
-
in a balanced position with your feet firmly on the ground. This is
how to use the saw correctly!
Always switch the motor off before you put the machine
down!.
•
Look over the working area and remove any obstructions.
•
Before starting work, check the safety of the machine (see
section "Before starting the machine").
•
Pick up the machine in both hands as specified.
•
Always saw at an adequate engine speed.
After use
•
Stop the engine.
•
Wait until all rotating parts have come to a standstill.
•
Place the sheath on the cutting mechanism.
•
Activate the chain brake.
•
Leave the machine to cool down.
•
Remove the spark-plug terminal.
Risk of kickback!
Kickbacks occur if the upper side or tip of the saw rail touches
wood or other solid objects. The device is thrown back towards
the user with great energy, possibly resulting in extremely serious
injuries.
Dangerous kickbacks may occur when working with the machine!
Extremely serious to fatal injuries may be the consequence!
Before starting work with the machine, check that the chain brake
is in perfect working order.
Ensure that the area of the saw rail shown in the diagram does not
touch wood or other solid objects.
To minimise the risk of injury in the event of a kickback, the
machine features a chain brake which is automatically actuated
by the kickback and immediately stops the chain. For reasons of
safety always check that the chain brake functions before using the
machine.
If kickbacks are less violent, the chain brake may not be actuated
automatically. For this reason it is important that the machine is
held firmly with both hands.
The risk of a kickback can only be reliably reduced by employing a
cautious and correct working method!
Werbung
