Basic Recommendations And Tips For Use; Map Creation - eta AURUM PRO Gebrauchsanleitung

BASIC RECOMMENDATIONS AND TIPS FOR USE

• Dual Wi-Fi network: If you have a smart Wi-Fi router in your home
that automatically switches the network frequency between
2.4 GHz and 5 GHz (within one SSID of the network name), there
may be problems with pairing or disconnection from the Internet
during operation. If these problems occur, we recommend switching
the router to broadcast two separate frequencies (SSID names),
one at 2.4 GHz, the other at 5 GHz. This setting is usually set in the
administration interface of the Wi-Fi router. If you cannot change
this yourself, contact your network administrator or IT specialist.
• The robotic vacuum cleaner with laser navigation is able to navigate
excellently in space and thus clean up with high preciseness.
Under normal circumstances, it is able to recognize its position if
you replace it within one map to another place, although we don't
recommend it. Always start the robot, if possible, from the charging
station, and - if possible - don't manipulate with it.
• As soon as the robot once creates a map, avoid excessive changes
of the environment, which could confuse the robot, or which could
cause erasing the map. It could be, for example, replacement
of furniture, movement of some persons next to the robot (most
frequently, children:)), etc.
• If you have long corridors in your home (e.g. 6 m rectangular),
or several rooms of the same geometric shape without internal
obstacles, the robot may have difficulty recognizing its position. This
can be easily avoided by putting a so-called reference point in each
of them, or an obstacle (cabinet, box, vase, etc.) that will help the
robot identify a specific room more easily.
• Pay special attention to the doors. If you want to make available
a room for the robot, the door has to be open during mapping. To
the contrary, close the door. It is also possible not to close the door
and prohibit the robot from access by means of a prohibited zone.
• If you transfer the robot to another part of your house (to another
map), change this map directly in the application before switching-
on the robot. To the contrary (i.e. if you start the robot from another
place within a different map), the robot could be confused and could
draw a map incorrectly.
• If you are planning to use the robot, we recommend that you fully
charge it first.
• Ideally, always let the robot finish the cleaning task.
Don't interrupt it and don't enter more orders or operations
than is necessary.
• If the map is deleted or in case of non-standard behavior, first
restart the robot and then insert it manually into the charging station.

4. MAP CREATION

• Place correctly the charging station in
keeping with instructions in the manual.
• After that, place the vacuum cleaner onto
the charging station and wait until the
vacuum cleaner is fully charged.
1 • Make available all rooms, in which you
want to clean up regularly (open the
doors and remove all obstacles, which
could prevent the vacuum cleaner from
movement).
• Turn on the vacuum cleaner in automatic
cleaning mode and let it clean the entire
accessible space.
• The vacuum cleaner starts mapping the
available space. This operation may take
longer depending on the size of the floor area.
Important!
To create and save a new map, you must
vacuum cleaner to complete AUTO cleaning!
• If you would like to speed up this operation,
2
activate a pause during cleaning and temporarily
limit the already mapped space with a prohibited
zone (do not place the zone near the station
or the robot) - the robot will only clean the rest
of the unbounded space, thus shortening the
cleaning time.
To explore the map faster, you can first send
the robot using local cleaning to the edge of the
newly discovered map and then activate the
automatic cleaning, see above.
• As soon as the vacuum cleaner maps out
and cleans up the whole available area, it
3 will return back to the charging station.
• After that, you may save the map and
continue to work with it.
• If you want to save a map, click on
„Setting " (in the right lower corner).
4
• Select „Map management" in menu.
• Then, click on „Save" to save the map.
• Then the map will be available for possible
5 future loading and switching between
multiple maps. You can load the selected
map by clicking on
REMARKS:
• Save each map which you would like to use for a long time.
• In total, you can create an save up to 3 maps. This option may
be used, especially, in case of multistage houses.
• If you want to create the next new map, always delete the actual map
so that the vacuum cleaner started on a clear screen.
• If the current map is updated (eg. with a new room that was
unavailable during mapping), save the map again after cleaning
and this update is complete.
ENG
„Use map".
ENG - 36