Werbung
BASIC MODE
MODEL RAS-32CNH1
ies a
ee On ee
Changes
from "H?* to "Med" or
. Runs at "Hi? until first thermo
off after operation is started.
. Runs at "Lo" when thermo is
oft.
Set to "ultra-Hi" when the
compressor runs at maximum
speed, and to "Hi" in other modes.
Operates at "Hi" regardiess of the
foom temperature.
Fan
speed
mode
(indoor
fan)
Operates at "Med" regardiess of
the room temperature.
Operates at "Lo" regardless of the
room temperature.
Performs only fan operation
at the
set speed regardiess
of the room
¢ Enters sleep operation after set
(with sleep button ON) | as on the left.
HITA-02976 / Druck:7
function select button only, not including
— — —
——————
oro are
LS
ee
Ye edd
(Otf->On timer) (On->Off timer) (On->Off timer
Changes between "Lo" and "Med"
depending on the room temperature.
1. The indoor fan also stops when the
compressor
is in stop status.
Set
to "Hi' in modes other than when the
compressor stops.
Set to "Med" in modes other than when the
compressor stops.
Set to "Lo" in modes other than when the
compressor stops.
during operation)
Set to "uitra-Lo', "Lo", "Med", "Hi", "ultra-Hi" or "stop" depending on the room temperature,
time and heat exchange temperature. Set to "stop" if the room temperature Is 18°C in the
"ultra-Lo" mode other than during preheating (cooling is recovered at 18.33°C).
When the compressor is running at maximum speed
In modes other than
during hot dash or when recovered from defrosting.
left
Set to "ultra-Lo", "Lo", "Med", "HI", "uitra-Hi" or "stop" depending on the room temperature and
time. Set to "stop" if the room temperature is 18°C in the "ultra-Lo" mode other than during
preheating (cooling is recovered at 18.33°C).
Set to "ultra-Hi when the compressor is running at maximum speed during hot dash or when
fecovered from defrosting.
Set to "ultra-Lo", "Lo", "Med" or "stop" depending on the room temperature and time. Set to
"stop" if the room temperature is 18°C in the "ultra-Lo" mode other than during preheating
(cooling is recovered at 18.33°C).
Set to "ultra-Lo", "Lo", or "stop" depending on the room temperature and time. Set to "stop" if
the room temperature is 18°C in the "ultra-Lo" mode other than during preheating (cooling is
recovered at 18.33°C). The fan speed is controlled by the heat exchanger temperature; the
overload control is executed as in the following diagram:
Heat
Special auto (not normally used)
The neuro & fuzzy control allows device to determine optimum
operation mode and set temperature. However, during auto
cooling,
the new cool rhythm starts when the room temperature
is less than the set temperature plus 0.66°C, after dash is
finished.
The special auto mode is based on N&F
auto, but the following is different:
The special auto operation mode is
entered when operation is started in the
following status:
<Start condition>
Power is supplied while the tele-control
signal is being input. (Operation starts
automatically.)
Notes:
(1) The set temperature can be varied +3°C using the
temperature setting buttons " and v.
(2) If operation is started by tele-contro! or by temporary switch
in status where remote control has not been used after
power was supplied, the operation mode will be as follows
(since there is no stored calendar data):
we imma |
<End condition>
The remote control restores the normal
operation mode.
Note
(1) Since there is no stored calendar
data, N&F control is not determined.
See Note (2) of N&F auto.
Dehumiditying | Set temperature: Room temperature at operation
'
start
Fan mode:
Auto
Set temperature:
22°C
Fan mode: Auto
Room
temperature
at operation
start
(°C)
¢ Same as at left.
« Performs the sleep operation of each operation mode.
Notes:
1. The voltages set for the fan motor in each operation mode are as shown in Table 1.
2. The set room temperatures in the diagram include the shift values in Table 2.
—55-
Werbung
