Werbung
Verfügbare Sprachen
Verfügbare Sprachen
I
FITTING THE TUBELESS TYRE
� Warning
If you have any doubt about your ability to carry out the fol-
lowing operations, please consult qualified personnel.
Always wear protective gloves and goggles before any mainte-
nance work on your wheels.
Check that the tyre bears the Tubeless Ready logo
If required to use a lever to insert the tyre beads, use a plastic
lever so to not damage the rim and tape.
To install the Tubeless ready tyre, please follow the following sim-
ple steps:
• Moisten the base of the rim with soap and water.
• Starting from the valve area, insert the firstof the two tyre beads
into place, and continue along the entire circumference of the
wheel.
• Fit the other bead of the tire and continue around the whole cir-
cumference of the rim: check the correct positioning of the tire
on both sides of the valve zone. Ensure the correct positioning
of the tire moving slightly back and forth the tire.
If the tyre is too easy to fit, the tyre may be too big. Caution, a tyre
that is too big could deflate suddenly and cause an accident,
serious injury or death.
II
INFLATING THE TUBELESS TYRE
� Warning
If you have any doubt about your ability to carry out the fol-
lowing operations, please consult qualified personnel.
Always wear protective gloves and goggles before any mainte-
nance work on your wheels.
Before inflating the Tubeless ready tyre, insert the anti-puncture
liquid (Caution, do not use products containing ammonia) fol-
lowing these simple steps:
• Remove the valve cap.
• Using your index finge, gently press the top of the valve so as to
ensure there is no air inside the tire.
• Remove the top part of the valve using the appropriate tools.
• Insert the anti-puncture liquid using the appropriate dispenser.
• Spin the wheel around several times to distribute the liquid
throu-ghout the inside of the tire.
• Put the top part of the valve back into place.
• Make sure the two tire beads are positioned correctly by ve-
rifying that the distance between the center line of the tyre and
the edge of the rim is constant through the entire wheel.
• Inflate the tyre. Warning, follow the steps in section 2 of the
General Indications.
• Put the valve cap back.
• Have a ride of 3-4 kms to ensure the liquid inside the tyre will
evenly distribute.
In the event of a tyre puncture, the loss of air is slow and not im-
mediate, and in some cases offers you the possibility of continu-
ing your ride home. Keep in mind that a Tubeless ready tyre can be
repaired by applying a tyre patch, by using an anti-puncture spray,
or by installing an inner tube.
10 SYNTIUM AERO / MICHE.IT
III
INSERTING AN INNER TUBE IN A TUBELESS TIRE IN
THE EVENT OF A PUNCTURE
The inner tube must have a Presta valve 6mm diameter.
• Deflate the tie.
• Completely deflate the tyre.
• Starting from the opposite side of the valve, unhook the tyre
bead from its seat and continue along the circumference of the
wheel. If required to use a lever to unhook the tyre beads, use a
plastic lever so to not damage the rim and tape.
• Unscrew the valve nut and remove the valve.
• Drain the puncture prevention liquid from inside the tyre and
rim.
• Insert the inner tube partially inlfated into the tyre.
• Starting from the point opposite the valve, insert the second tire
bead into place and continue along the entire circumference of
the wheel, taking care to not pinch the inner tube.
• Inflate the inner tube until both tire beads are fitted properly in
the correct position.
IV
CHANGE FROM CLINCHER TIRE TO TUBELESS
READY TIRE
� Warning
The standard supplied rim tapes are not suitable for Tubeless
Ready tyres wheels conversion.
If you wish to convert your Miche wheels to Tubeless Ready tyres
use, please use rim sealing kits with the following features:
• conical insert valve
• bidirectional woven cloth glued tape (width 15 mm for total cir-
cumference)
• high pressure resistance sealing tape (width 21 mm for total
circumference)
Werbung
