Ryobi RDP102L Bedienungsanleitung Seite 12

■
Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
■
Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
■
Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
■
Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
■
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
■
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking
into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could result
in a hazardous situation.
■
Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
SERVICE
■
Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
DRILL PRESS SAFETY WARNINGS
■
The drill must be secured. A drill that is not
properly secured may move or tip over and may
result in personal injury.
■
The workpiece must be clamped or secured to
the workpiece support. Do not drill pieces that
are too small to be clamped securely. Holding the
workpiece by hand during operation may result in
personal injury.
■
Do not wear gloves. Gloves may be entangled by
the rotating parts or chips leading to personal injury.
■
Keep your hands out of the drilling area while the
tool is running. Contact with rotating parts or chips
may result in personal injury.
■
Make sure the accessory is rotating before
feeding into the workpiece. Otherwise the
accessory may become jammed in the workpiece
12
Original Instructions
causing unexpected movement of the workpiece and
personal injury.
■
When the accessory is jammed, stop applying
downward pressure and switch off the tool.
Investigate and take corrective actions to
eliminate the cause of the jam. Jamming can
cause unexpected movement of the workpiece and
personal injury.
■
Avoid generating long chips by regularly
interrupting downward pressure. Sharp metal
chips may cause entanglement and personal
injuries.
■
Never remove chips from the drilling area while
the tool is running. To remove chips, move the
accessory away from the workpiece, switch
off the tool and wait for the accessory to stop
moving. Use tools such as a brush or hook to
remove chips. Contact with rotating parts or chips
may result in personal injury.
■
Accessories with speed ratings must be rated at
least equal to the maximum speed marked on the
power tool. Accessories running faster than their
rated speed can break and fly apart.
■
Keep bits clean and sharp. Sharp bits minimize
stalling. Dirty and dull bits may cause misalignment
of the material and possible operator injury.
■
Keep hands away from work area. Keep hands
away from the bit. Restrain any loose clothing,
jewellery, long hair, etc., that may become entangled
in the bit.
■
Always clamp workpiece or brace against
column to prevent rotation. Never use your hand
to hold the object while drilling.
■
Use recommended speed for drill accessory and
workpiece material.
■
Be sure drill bit or cutting tool is securely locked
in the chuck.
■
Be sure chuck key is removed from the chuck
before connecting to power source or turning power
on.
■
Adjust the table or depth stop to avoid drilling
into the table. Shut off the power, remove the drill
bit, and clean the table before leaving machine.
■
Avoid direct eye exposure when using the laser
guide.
■
Always ensure the laser beam is aimed at a
surface without reflective properties. Shiny
reflective materials are not suitable for laser use.
■
Never place your fingers in a position where they
could contact the drill or other cutting tool if the
workpiece should unexpectedly shift.
■
Never perform any operation by moving the head
or table with respect to one another. Do not turn
the motor switch on or start any operation before
checking that the head and table support lock handle
is clamped tight to column and head and table
support collars are correctly positioned.
■
Before engaging the power switch, make sure