Ryobi RDP102L Bedienungsanleitung Seite 15

ASSEMBLY AND ADJUSTMENTS
WARNING
For your own safety, never connect plug to power
source outlet until all assembly steps are complete
and you have read and understood the safety and
operating instructions.
WARNING
The drill press is a heavy power tool and should be
lifted with the help of two people or more to safely
assemble it.
ASSEMBLING COLUMN TO BASE
See Figure 5.
1. Place the base on a fl at, stable surface.
2. Align screw holes in the column assembly with screw
holes in the base.
3. Place a hex bolt in each hole.
4. Tighten each hex bolt using an adjustable wrench.
INSTALLING TABLE TO COLUMN ASSEMBLY
See Figures 6-10.
1. Insert the table bracket lock handle into the threaded
hole at the rear of the table bracket.
NOTE: Install the handle from left to right, so it enters
the non-threaded side of the table bracket first.
2. Feed the worm gear through the table crank hole in
the table bracket. Make sure the worm gear meshes
with the inside gear.
NOTE: Do not remove the lubrication from the worm
gear.
3. Feed the rack through the slot in the table bracket so
that the teeth are facing out and the longer smooth
end faces up. The worm gear should engage the
rack.
4. Using both hands, slide the entire table and rack onto
the column until the bottom of the rack is positioned
in the base collar and against the column.
5. Tighten the table bracket lock handle to lock the
table assembly to the column.
NOTE: Do not overtighten.
6. Slide the rack ring, bevel-side down, over the column
until the beveled side engages the beveled end of
the rack.
7. Tighten the set screw in the collar using the hex key.
To avoid column or collar damage, do not overtighten
the set screw.
NOTE: You should be able to move the table from
side to side.
8. Install table crank handle over the end of worm gear
so that the fl at side of the shaft aligns with the set
screw.
9. Tighten the set screw using the hex key.
INSTALLING THE HEAD
See Figure 11.
WARNING
The Drill Press head is heavy and should be lifted
with the help of two people to safely assemble the
drill press head on the column.
1. Position the head onto the column with the chuck
positioned over the table.
NOTE: The product is heavy. Get help when needed.
2. Slide the head down as far as it will go. Align the
table assembly with the base and then tighten the
two head set screws with the hex key.
INSTALLING FEED HANDLES
See Figure 12.
1. Attach the three feed handles by screwing them into
the threaded holes in the hub assembly.
INSTALLING THE CHUCK
See Figures 13-15.
WARNING
Before any assembly of the chuck to the drill press
head, clean all mating surfaces with a non-petroleum
based product. Any oil or grease used in the packing
of these parts must be removed otherwise the chuck
may come loose during operation.
1. Clean out the tapered hole in the chuck with a clean
cloth and a non-alcohol based cleaner. Wipe clean
all oil residue and any dirt or grime thoroughly.
2. Clean tapered surfaces on the spindle in the same
manner as above.
NOTE: Make sure there are no foreign particles
sticking to the surfaces. The slightest piece of dirt or
oil residing on any of these surfaces will prevent the
chuck from seating properly. This will cause the drill
chuck and bit to wobble.
3. Position chuck on spindle. Chuck should be fully
opened to avoid damaging jaws.
4. Unlock the table support lock and swing the table
away from the bottom of the chuck.
5. Insert the chuck onto the spindle, pushing upwards
all the way.
6. Using a piece of scrap wood to protect the chuck,
fi rmly tap the chuck into place using a mallet or
hammer.
CAUTION
Risk of property damage. To avoid damage to the
chuck, never drive the chuck on the spindle with a
metal hammer.
Original Instructions
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
15