Aiwa ACD-24KBTU Gebrauchsanweisung, Installationsanleitung Seite 11

This adjustment must be done while the appliance is
switched off
Never position Flaps manually, the delicate
mechanism might seriously damaged!
Never put fingers, sticks or other objects into the air
inlet or outlet vents. Such accidental contact with
live parts might cause unforeseeable damage or
injury.
TURBO function
To activate turbo function, press the
TURBO
TURBO button, and
the display.
Press again to cancel this function.
In COOL/ HEAT mode, when you select TURBO feature,
the appliance will turn to quick COOL or quick HEAT
mode, and operate the highest fan speed to blow
strong airflow.
MUTE function
MUTE
Press MUTE button to active this function, and
1.
will appears on the remote display. Do it again to
deactivate this function.
2. When the MUTE function runs, the remote
controller will display the auto fan speed, and the
indoor unit will operate at lowest fan speed to be
quiet feeling.
3.
When press FAN/ TURBO/ SLEEP button, the MUTE
function will be cancel. MUTE function can not be
activated under dry mode.
SLEEP function
Pre-setting automatic operating
SLEEP
program.
Press SLEEP button to activate the
SLEEP function, and appears on the display. Press
again to cancel this function.
After 10 hours running in sleep mode, the air
conditioner will change to the previous setting
mode.
I FEEL function (Optional)
Press I FEEL button to active the
I FEEL
function, the will appear on the remote
display. Do it again to deactivate this
function.
This function enables the remote control to measure
the temperature at its current location, and send this
signal to the air conditioner to optimize the temperature
around you and ensure the comfort.
It will automatically deactivate 2 hours later.
ECO function
In this mode the appliance automatically
ECO sets the operation to save energy.
Press the ECO button, the
the display, and the appliance will run in ECO mode.
Press again to cancel it.
Note: The ECO function is available in both
COOLING and HEATING modes.
DISPLAY function
DISPLAY
switch on the LED display.
GEN function (Optional)
1. Turn on the indoor unit at first, and long press
MUTE button 3 seconds to active, and do it again to
deactivate this function.
2.
Under this function, short press MUTE button to
select the General type L3 - L2 - L1 - OF.
will appear on
3.
Select OF and wait 2 seconds to exit it.
* If the indoor unit displays "0A", please use the remote
to raise the operating gear of the GEN mode, and the
compressor will restart after stopping for 3 minutes.
SELF-CLEAN function (Optional)
Only optional for some heating pump inverter
appliance.
To active this function, turn off the indoor unit at first,
then press
toward the indoor unit, until hear a beep, and AC will
appear on the remote controller display and the indoor
LED display.
1. This function helps carry away the accumulated dirt,
bacteria, etc from the indoor evaporator.
2. This function will run about 30 minutes, and it will
return to the pre-setting mode. You can press
to cancel this function during the process.
You will hear 2 beeps when it's finished or cancelled.
It's normal if there is some noise during this
function process, as plastic materials expand with
heat and contract with cold.
We suggest operating this function at the
following ambient conditions to avoid certain
safety protection features.
It's suggested to utilize this function every
3 months.
8ºC HEATING function (Optional)
1. Long press ECO button over 3 seconds to active
this function, and 8ºC ( 46ºF ) will appear on the
remote display.
2.
Do it again to deactivate this function 8ºC 46ºF This
function will auto start the heating mode when the
room temperature is lower than 8ºC (46ºF), and it
will return to standby if the temperature reaches
9ºC (48ºF).
appears on
3.
If the room temperature is higher than 18ºC
(64ºF), the appliance will cancel this function
automatically.
Switch ON/OFF the LED display on panel.
Press DISPLAY button to switch off the
LED display on the panel. Press again to
SWING
and button at the same time
SWING
Indoor unit Temp < 86ºF (30ºC)
Outdoor unit 41ºF (5ºC) < Temp < 86ºF(30ºC)
EN
button
ACD-24KBTU 11