Child-Lock Function - Aiwa ACD-24KBTU Gebrauchsanweisung, Installationsanleitung

COOLING MODE
The cooling function allows the air
COOL conditioner to cool the room and reduce
Air humidity at the same time.
To activate the cooling function (COOL), press the
MODE button until the symbol
display.
With the button or set a temperature lower
than that of the room.
FAN MODE (Not FAN button)
Fan mode, air ventilation only.
FAN To set the FAN mode, press MODE until
appears on the display.
DRY MODE
This function reduces the humidity
DRY
of the air to make the room more
comfortable.
To set the DRY mode, Press MODE until
in the display. An automatic function of pre-setting is
activated.
AUTO MODE
Automatic mode.
To set the AUTO mode, press MODE
AUTO
until appears on the display.
In AUTO mode the run mode will be set
automatically according to the room temperature.
HEATING MODE
The heating function allows the air
HEAT
conditioner to heat the room.
To activate the heating function (HEAT),
press the MODE button until the
the display.
With the button or set a temperature higher than that
of the room.
In HEATING operation, the appliance can
automatically activate a defrost cycle, which
is essential to clean the frost on the condenser
so as to recover its heat exchange function.
This procedure usually lasts for 2-10 minutes.
During defrosting, indoor unit fan stop
operation. After defrosting, it resumes to
HEATING mode automaticall
FAN SPEED function (FAN button)
Change the operating fan speed.
FAN Press button FAN to set the running fan
speed,
it can be set to AUTO/ MUTE/ LOW/ LOW-MID
/ MID/ MID-HIGH/ HIGH/ TURBO speed circularly.

CHILD-LOCK FUNCTION

1.
Long press MODE and TIMER button together to
active this function, and do it again to desactivate
this function.
2. Under this function, no single button will active.
10 ACD-24KBTU
TIMER function ---- TIMER ON
TIMER
To set the time of automatic switch-on as below:
appears on the
1.
2.
3.
4.
appears
CANCEL it by press TIMER button.
TIMER function ---- TIMER OFF
TIMER
To set the time of automatic switch-on as below:
When the unit is switch-on, you can set the TIMER OFF.
1.
2.
3.
CANCEL it by press TIMER button.
Note: All programming should be operated within 5
symbol appears on
seconds, otherwise the setting will be
cancelled.
SWING function
1. Press the button SWING to activate the louver,
2. If the vertical deflectors are positioned manually
which placed under the flaps, they allow to move the air
flow direct to rightward or leftward.
3. For some inverter heating models, press horizontal
SWING and vertical SWING together button at the same
time, it will activate the Self-Clean function.
To automatic switch on the appliance.
When the unit is switch-off, you can set
the TIMER ON.
Press TIMER button first time to set the switch-on,
and will appear on the remote display and
flashes.
Press or to button to set desired Timer-on time.
Each time you press the button, the time increases/
decreases by half an hour between 0 and 10 hours
and by one between 10 and 24 hours.
Press TIMER button second time to confirm.
After Timer-on setting, set the needed mode (Cool/
Heat/ Auto/ Fan/ Dry), by press the MODE button.
And set the needed fan speed, by press FAN
button. And press or to set the needed operation
temperature.
To automatic switch off the appliance.
When the unit is switch-off, you can set
the TIMER ON.
Confirm the appliance is ON.
Press the TIMER button at first time to set the
switch-off.
Press TIMER button at the second time to confirm.
SWING
SWING
1.1 Press to activate the horizontal flaps to
swing from up to down, the will appear on the
remote display. Press again to stop the swing
movement at the current angle.
1.2 Press to active the vertical deflectors to
swing from left to right, the will appear on the
remote display.
Press again to stop the swing movement at the
current angle.