Husqvarna 1-8DPF40 Bedienungsanweisung Seite 8

• Make sure that the ON/OFF switch is in OFF position
before the product is connected to the power supply.
• Always disconnect the power plug during a long
product stop.
• Do not use the product if the supply cord or power
plug is damaged. If the supply cord is damaged, it
must be replaced by the manufacturer, its service
agentor similarly qualified persons in order to avoid
a hazard. A damaged power cord can cause serious
injury and death.
• Use the power cord correctly. Do not use the power
cord to move, pull or disconnect the product. Pull the
power plug to disconnect the power cord. Do not pull
the power cord.
• Only operate the product on dry surfaces.
• Keep the product away from rain. Water that goes
into the product increases the risk of electrical shock.
• Always disconnect the power cord before you
connect or disconnect the connection for the motor
cable and the electrical enclosure.
• In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance
must not be supplied through an external switching
device, such as a timer, or connected to a circuit that
is regularly switched on and off by the utility.
• Make sure that the power supply for the product is
supplied by separate transformers that are used for
industrial purpose only.
Grounded product instructions
WARNING:
result in electrical shock. Speak to an
approved electrician if you are not sure if
your mains outlet is correctly grounded.
Do not do modifications to the power plug
from its factory specification. If the power
plug or power cord is damaged or must be
replaced, speak to your Husqvarna service
agent. Obey local regulations and laws.
If you do not fully understand the
instructions about the grounded product,
speak to an approved electrician.
Use only grounded outdoor extension cables with
grounding plugs and grounding outlet that accepts the
product power plug.
The product has a grounded power cord and power
plug. Always connect the product to a grounded mains
outlet. This decreases the risk of electrical shock.
Do not use electrical adapters with the product.
Extension cables
• Use only approved extension cables with applicable
properties.
8
Incorrect connection can
• The rated value on the extension cable must be the
same or higher than given on the rating plate of the
product.
• Use grounded extension cables.
• When you operate the product outdoors, use
an extension cable that is applicable for outdoor
operation. This decreases the risk of electrical
shock.
• Keep the connection to the extension cable dry and
off the ground.
• Keep the extension cable away from heat, oil, sharp
edges or moving parts. A damaged cable increases
the risk of electrical shock.
• Make sure that the extension cable is in good
condition and not damaged.
• Do not use the extension cable while it is wound up.
This can cause the extension cable to become too
hot.
• Make sure that the extension cable is out of the
way and the product during operation. This prevents
damage to the extension cable.
Safety devices on the product
WARNING:
instructions that follow before you use the
product.
• Do not use the product if the safety devices are
damaged or does not operate correctly.
• Do a check of the safety devices daily. If your safety
devices are damaged or does not operate correctly,
speak to your Husqvarna service agent.
• Do not make modifications on safety devices
ON/OFF switch
The ON/OFF switch is used to start and stop the power
supply to the product.
To do a check of the ON/OFF switch
Product overview on page 3 for information
Refer to
about where the ON/OFF switch is on your product.
1. Turn the emergency stop button clockwise to make
sure that the emergency stop button is disengaged.
2. Turn the ON/OFF switch to ON postion.
3. Make sure that the power supply starts.
4. Turn the ON/OFF switch to OFF position.
5. Make sure that the power supply stops.
ON/OFF buttons of the blastmotor
The ON/OFF buttons of the blastmotor are used to start
and stop the blastmotor. Refer to
ON/OFF buttons of the blastmotor on page 9 .
Read the warning
To do a check of the
2124 - 001 - 13.04.2023